manualshive.com logo in svg

Sharp JH-3500U, Installation & Operator'S Manual, Page: 2 / 33

Share
Download
Sharp JH-3500U Installation & Operator'S Manual Download Page 2

i

Notice for Users in the USA

FCC Statement

WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by
the manufacturer could void the user’s authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the
FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.  However, there is no guarantee that interference will not
occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.

Summary of Contents for JH-3500U


































Reviews:

No comments