Sharp IMAGER AR-5316 Service Manual Download Page 47

Page: 47 / 56

AR-5316 FLASH ROM VERSION UP PROCEDURE 12-1

[12]FLASH ROM VERSION UP PROCEDURE

1.Preparation

Write the download data (the file with the extension dwl) to the main body

of AR-5316.

Necessary files for download

• Maintenance.exe (Maintenance software)

• ProcPegasus.mdl

• ProcPegasus.ini
• ProcPegasus.fmt

• Pegasus.inf

• Usbscan.sys
• Download file:***.dwl

<Note>
•The Download file(***.dwl ) and the like that are to be downloaded

should be copied, in advance, into folders that have a maintenance

program.

•When creating a folder for a maintenance tool in the PC, be sure that no

lengthy folder name is included in the path.

(Example)

Incorrect c:\Maintenance Download Tool

Correct c:\Maintenance\Downtool

2.Download procedure

1) Main body side:

Executable by performing the Service Simulation No. 49-01 (Flash
Rom program-writing mode).

(A word "d" appears on the operation panel to denote the download

mode status. )

2) Connect the PC and the main body with the download cable

(USB cable).

(Be sure to use a USB cable for connection. USB2.0 of the AR-EB7
is not applicable.)

3) PC side:

Boot the maintenance program. Select the model icon.

4) PC side:

Confirm that the "Simulation Command List" tree is displayed on the

maintenance program.

5) PC side:

When the message "the main body has not got started running" is

displayed on the lowest area of the figure below after the
"maintenance program" is started up, select the "File" and then

"Reconnect" in the menu bar.

6) PC side:

Confirm a tree is displayed under the "Special (MCU/IMC2/FAX)" on

the maintenance program". (If no tree is displayed, confirm that the

USB is connected and select the "Reconnect" (the above 5) again.)

[12]FLASHROM.fm 1 ページ２００５年７月１日金曜日午後５時３１分

Summary of Contents for IMAGER AR-5316

























































Search results

Summary of Contents for IMAGER AR-5316

Reviews:

Related manuals for IMAGER AR-5316

Brands by name

Popular brands

Sharp IMAGER AR-5316, Service Manual

Search results

Summary of Contents for IMAGER AR-5316

Reviews:

Related manuals for IMAGER AR-5316

Brands by name

Popular brands