FO-DC500U
FO-DC600U
– 4 –
: Change/Addition
[2] Diagnostics and service soft switches
1. Operating procedure
Two kinds of diagnoses are supported.
1-1. Fax diagnosis
This diagnosis is concerned with the main body of fax which is used for
production and service support.
Entering the diagnostic mode
MENU
9
8
7
START
A
SOFT SWITCH MODE
START
B
PRINT AREA
START
C
ROM & RAM CHECK
START
D
AUTO FEEDER MODE
START
E
AGING MODE
START
F
PANEL CHECK MODE
START
G
OPTICAL ADJUST MODE
START
H
PRODUCT CHECK
START
I
SIGNAL SEND MODE
START
J
COMM. CHECK MODE
START
K
MEMORY CLEAR MODE
START
L
FLASH MEMORY CHECK
START
M
ALL FAX/TEL. ENTRY MODE
START
START
N
O
CONF. PASSCODE
START
P
SIGNAL SEND MODE 2
START
Q
TA69 or TA70
START
DEPT. PASSCODE
MENU
9
8
7
Press
, and the following
display will appear.
START
Then press the
key. Select the desired item with the
key
and the
key or select with the rapid key.
Enter the mode with the
START
key.
(Diag
•
specifications)
MEMORY SET MODE
START
R
STAMP AGING MODE
START
S
DIAL TEST MODE
START
T
U
COPY DIAG MODE
LCD CHECK MODE
V
PERSONAL BOOK LIST
START
W
FONT LIST PRINT MODE(*)
START
START
X
NO FUNCTION
START
1
st
Line
2
nd
Line
3
rd
Line F/W
version
4
th
Line
NIC board version
5
th
Line
PCL board version
6
th
Line
7
th
Line Memory
size
8
th
Line
GATE arrayA/B version
9
th
Line
FAX : TA69 or TA70
NIC
:x.xxx
PRN :xxxx
PRN MEMORY SIZE = 16(MB)
GAA : ESx
GAB : ESx
*: FONT LIST PRINT MODE can be used only when the
network function is effective.
Y
NO FUNCTION
START
Z
UPGRADE SETTING
START
S) Dial test mode
The mode is used to inspect whether dialing is accurate in two kinds of
dial modes . All data which can be dialed in this mode are automatically
called up in both PB mode and DP mode.
[In case that 2 line optional is not mounted.]
1
Turn on CML, and dial the following in the PB mode.
1, 2, 3, 4, 5, 6, 7, 8, 9, , 0, #
2
Dial the following in the DP mode.
1, 5, 9, 0
3
After dialing, turn off CML.
NOTE:
This mode uses the ordinary auto dial. (Accordingly, the signal sending
time and minimum pause are all the same as ordinary.
The measurement result in this mode is completely all the same as in
the ordinary dial mode.)
T) Copy diag mode
This mode is for automatic mode selection of copy to reduce the time for
treatment at the time of production.
1
Set 2 sheets of document. (No problem if there are 2 sheets or
more.)
2
3 sheet continuous copy: 1st sheet in the FINE AUTO
2nd sheet and after that are copied in the
H-TONE DARK.
NOTE: Input of the image quality and the darkness keys is invalid in this
mode.
U) LCD check mode
This is an item to check that the LCD acts normally.
1
The screen for selecting the contrast adjustment mode and the “H”
display mode appears.
2
Select the mode using the “
←
” or “
→
” keys or otherwise dial keys “1”
or “2”.
[When the contrast adjustment mode is selected]
3
Adjust with the “
←
” or “
→
” keys so that both right and left halves of
the “A” can be recognized.
[When the “H” display mode is selected]
3
Turn on the backlight so that the whole screen shows “H”.
(26 letters x 9 lines)
V) Personal book list
The PASSCODE of the personal book 00 to 10 are output.
W) Font list print mode
[Only when network function is mounted]
The font list that can be used in the network function is printed.
X) No function
Y) No function
Z) Upgrade setting
After upgrading from version TA69D or earlier to TA69F or later on
FO-DC500U, or after upgrading from version TA70C or earlier to TA70E
(Sep. version) or later on FO-DC600U, enter this mode to use new
functions.
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHH
U:LCD CHECK MODE
1=CONT.ADJ 2=TEST DISP
CONTRAST=-9 TEMP=+25
A
