Sharp FO-4450, Service Manual

Page: 46 / 170

FO-4450U/FO-CS1
2 – 32
SW66 No. 1 ~ No. 3 The 3rd priority cassette
To select the third priority cassette.
SW66 No. 4, No. 5 Cassette selection of separate page
The supply origin of a separate page is set.
SW66 No. 6 Reserved
Set to "0".
SW66 No. 7 Maximum size of input document
The maximum scan length can be switched.
SW66 No. 8 Print hold function
Use or disable Print Hold function.
SW67 No.1, No. 2 Power save mode
The heater mode of a printer is set.
SW67 No. 3 ~ No. 5 Density adjustment of print bias
The density of printing is set.
It can be also set in the print diagnosis mode.
SW67 No. 6, No. 7 Drum life detection
The detection mode of Drum life is set.
SW67 No. 8 Reserved
Set to "0".
SW68 No. 1, No. 2 Distinctive ring pattern
The distinctive ring patter is set for country.
SW68 No. 3, No. 4 Reserved
Set to "1".
SW68 No. 5, No. 6 Reserved
Set to "0".
SW68 No. 7 Reserved
Set to "1".
SW68 No. 8 Reserved
Set to "0".
SW69 No. 1 Reserved
Set to "1".
SW69 No. 2, No. 3 Reserved
Set to "0".
SW69 No. 4 Reserved
Set to "1".
SW69 No. 5 Reserved
Set to "0".
SW69 No. 6, No. 7 Reserved
Set to "1".
SW69 No. 8 Reserved
Set to "0".
SW70 No. 1 Reserved
Set to "1".
SW70 No. 2 Reserved
Set to "0".
SW70 No. 3 Reserved
Set to "1".
SW70 No. 4 ~ No. 7 Reserved
Set to "0".
SW70 No. 8 Reserved
Set to "1".
SW71 No. 1, No. 2 The default resolution for copying
In case of copying without pressing the RESOLUTION key, resolution
will be super fine.
SW71 No. 3 Reserved
Set to "0".
SW71 No. 4 Reserved
Set to "1".
SW71 No. 5 Reserved
Set to "0".
SW71 No. 6, No. 7 Picture quality priority mode
Used to set the transmission mode which is automatically selected when
the MODE key is not pressed. In the copy mode, however, the fine mode
is automatically selected unless the MODE key is manually set to an-
other mode.
SW71 No. 8 Reserved
Set to "0".
SW72 No. 1 Reserved
Set to "1".
SW72 No. 2 Reserved
Set to "0".
SW72 No. 3 Reserved
Set to "1".
SW72 No. 4 ~ No. 8 Reserved
Set to "0".
SW73 No. 1 ~ No. 5 Reserved
Set to "0".
SW73 No. 6 ~ No. 8 Data reduction
Reduction ratio of receiving is set .
It can be changed even in the optional mode.
To set printing reduction rate of received images.
SW74 No. 1 Automatic printing of activity report
This soft switch is used to select; whether or not to produce the activity
report when the memory is full (about 50 items). An activity report can
be produced when the following key entry command is made.
"FUNC", "2", "#", "START"
After producing the activity report, all the data in the memory will be
cleared.
When the switch function is set to "0" (NO), the data in memory will be
deleted from the oldest as it reaches the maximum memory capacity
(approx. 50 items).
SW74 No. 2 Print out of total time and total number of pages on
activity report
Used to make a choice of whether the total communication time and
pages are recorded in the activity report.
SW74 No. 3 Reserved
Set to "0".
SW74 No. 4 Department function
This model has the department audit feature, it has to be set to 1 to
utilize this feature.
SW74 No. 5 ~ No. 8 Department ID digit
Used to set the department ID digit number .
When set to "D" , the number is "4" .
SW75 No. 1 Copy protect switch
When this switch is set to “1”, copy is for bidden.
SW75 No. 2 Cut-off mode (when copy mode)
When in copy, if the scanned data is out of the range of recording, the
operator has one of the choices below using the switch.
0: Continue: Data is printed onto the next page with the last 20mm
also printed at the beginning of the next page.
1: Cut off: Data scanned out of the limit is cut off (a page is printed.)
000: Automatic
100: 100%
Except the above 100%
manuals4you.com manuals4you.com