XL-505/505C,CP-505B
– 2 –
Cassette deck section
Frequency response: 50 - 14,000 Hz (Normal tape)
Signal/noise ratio:
50 dB
Wow and flutter:
0.25 % (WRMS)
Type:
Full range speaker system
Speakers:
10 cm (4") full-range speaker
Rated input power:
5 W
Maximum input power: 10 W
Impedance:
4 ohms
Dimensions:
Width; 145 mm (5-3/4")
Height; 240 mm (9-1/2")
Depth; 183 mm (7-1/4")
Weight:
1.1 kg (2.4 lbs.)/each
General
Power source:
AC 120 V, 60 Hz
Power consumption:
30 W
Dimensions:
Width; 160 mm (6-5/16")
Height; 240 mm (9-1/2")
Depth; 250 mm (9-7/8")
Weight:
2.6 kg (5.7 lbs.)
Amplifier section
Output power:
RMS; 10 W (5 W + 5 W)
(10 % T.H.D.)
Output terminals:
Speakers; 4 ohms
Headphones; 16-50 ohms
(recommended; 32 ohms)
Tuner section
Frequency range:
FM; 87.5 - 108 MHz
AM; 530 - 1,720 kHz
Compact disc player section
Type:
Compact disc player
Signal readout:
Non-contact, 3-beam semi-
conductor laser pickup
D/A Converter:
1-bit D/A converter
Filter:
8-times oversampling digital filter
Frequency response: 20 - 20,000 Hz
Wow and flutter:
Unmeasurable
(less than 0.001% W.peak)
SPECIFICATIONS
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
Specifications for this model are subject to change without
prior notice.
XL-505/505C
CP-505B
IMPORTANT SERVICE NOTES (XL-505 ONLY)
BEFORE RETURNING THE AUDIO PRODUCT
(Fire & Shock Hazard)
Before returning the audio product to the user, perform the
following safety checks.
1. Inspect all lead dress to make certain that leads are not
pinched or that hardware is not lodged between the chassis
and other metal parts in the audio product.
2. Inspect all protective devices such as insulating materials,
cabinet, terminal board, adjustment and compartment
covers or shields, mechanical insulators etc.
3. To be sure that no shock hazard exists, check for leakage
current in the following manner.
* Plug the AC line cord directly into a 120 volt AC outlet.
* Using two clip leads, connect a 1.5k ohm, 10 watt resistor
paralleled by a 0.15
µ
F capacitor in series with all exposed
metal cabinet parts and a known earth ground, such as
conduit or electrical ground connected to earth ground.
* Use a VTVM or VOM with 1000 ohm per volt, or higher,
sensitivity to measure the AC voltage drop across the
resistor (See diagram).
* Connect the resistor connection to all exposed metal parts
having a return path to the chassis (antenna, metal cabinet,
screw heads, knobs and control shafts, escutcheon, etc.)
and measure the AC voltage drop across the resistor.
All check must be repeated with the AC line cord plug connection
reversed.
Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp.
AC.) or more is excessive and indicates a potential shock
hazard which must be corrected before returning the audio
product to the owner.
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
TEST PROBE
0.15 µ F
1.5k ohms
10W
VTVM
AC SCALE
