Sharp CD-SW440NH, Operation Manual, Page: 31 / 34

04/1/28 CD-SW440N_09 EN
E-22
9
1
7
6
5
4
3
2
1
Enhancing your system
The connection lead is not included. Purchase a
commercially available lead as shown below.
Note:
To prevent noise interference, place the unit away from the
television.
●
Do not turn the volume on to full at switch on and listen
to music at moderate levels. Excessive sound pressure
from earphones and headphones can cause hearing
loss.
●
Before plugging in or unplugging the headphones,
reduce the volume.
●
Be sure your headphones have a 3.5 mm (1/8")
diameter plug and impedance between 16 and 50
ohms. The recommended impedance is 32 ohms.
●
Plugging in the headphones disconnects the speakers
automatically. Adjust the volume using the VOLUME
control.
Troubleshooting chart
Many potential problems can be resolved by the owner
without calling a service technician.
If something is wrong with this product, check the following
before calling your authorised SHARP dealer or service
centre.
1
Use a connection lead to connect the portable audio
player etc. to the AUDIO IN socket. When using video
equipment, connect the audio output to this unit and
the video output to a television.
2
Press the ON/STAND-BY button to turn the power on.
3
Press the AUDIO IN button on the remote control or
FUNCTION button repeatedly on main unit to select
AUDIO IN function.
4
Play the connected equipment. If volume level of the
connected device is too high, sound distortion may
occur. Should this happen, lower the volume of the
connected device. If volume level is too low, increase
the volume of the connected device.
FUNCTION FUNCTION
AUDIO IN AUDIO IN
PHONE S PHONE S
VOL VOL
ON/ S TAND-BY ON/ S TAND-BY
M I N I C O M P O N E N T S Y S T E M
CD- S W440
PU S H PU S H
OPEN OPEN
AUDIO IN AUDIO IN
PHONE S PHONE S
Audio cable
(not supplied)
Portable audio
player, etc.
Listening to the playback sounds of
portable audio player, etc.
Headphones
Symptom Possible cause
●
The clock is not set
to the correct time.
●
Did a power failure occur?
Reset the clock. (Refer page
20)
●
When a button is
pressed, the unit
does not respond.
●
Set the unit to the power
stand-by mode and then turn
it back on.
●
If the unit still malfunctions,
reset it. (Refer page 23)
●
No sound is heard.
●
Is the volume level set to
“0”?
●
Are the headphones
connected?
●
Are the speaker wires
disconnected?
Symptom Possible cause
●
Playback does not
start.
●
Playback stops in
the middle or is not
performed properly.
●
Is the disc loaded upside
down?
●
Does the disc satisfy the
standards?
●
Is the disc distorted or
scratched?
●
Playback sounds
are skipped, or
stopped in the
middle of a track.
●
Is the unit located near
excessive vibrations?
●
Is the disc very dirty?
●
Has condensation formed
inside the unit?
Symptom Possible cause
●
The remote control
does not operate.
●
Is the AC power lead of the
unit plugged in?
●
Is the battery polarity
correct?
●
Are the batteries dead?
●
Is the distance or angle
incorrect?
●
Does the remote control
sensor receive strong light?
Symptom Possible cause
●
Sound skipping.
●
Cannot hear treble.
●
Sound Fluctuation.
●
Is there any slack?
●
Is the tape stretched?
●
Are the capstans, pinch
rollers or heads dirty?
●
Cannot remove the
tape.
●
If a power failure occurs
during playback, the heads
remain engaged with the
tape. Do not open the
compartment with great
force.
General
CD player
Remote control
Cassette deck