manualshive.com logo in svg

Sharp AR-207, Operation Manual

The Sharp AR-207 Operation Manual is a comprehensive guide for efficiently operating and maintaining your Sharp AR-207 printer. This detailed manual is available for free download from our website, providing you with step-by-step instructions and valuable information to optimize your printing experience.

Share
Download
background image

42

ST
A

TUS

INDICA

T

ORS

1

Open the bypass tray. Lift slightly on the side cover
and slide the cover out until it stops.

2

Push gently on both sides of the front cover to open the
cover.

3

Push the toner cartridge lock release lever and pull the
toner cartridge out. Remove the toner cartridge while
supporting it with the left hand at the green label position.

●

For disposal of the old toner cartridge, contact your dealer.

4

Remove the new toner cartridge from the bag. Hold the
cartridge on both sides and shake it horizontally four or
five times.

 TONER  CARTRIDGE  REPLACEMENT

 Toner cartridge replacement

Toner cartridge lock 
release lever

4 or 5 times

GENUINE SUPPLIES

For best copying results, be sure to use only
SHARP Genuine Supplies which are designed,
engineered and tested to maximize the life and
performance of SHARP copiers. Look for the
Genuine Supplies label on the toner package.

When the toner cartridge replacement required (

) indicator lights up,

replacement of the toner cartridge will be needed soon. Obtain a new
cartridge. When the toner cartridge replacement required (

)  indicator

blinks, the toner cartridge must be replaced before copying can be resumed.
Replace the toner cartridge by following the procedure below.

During a long copy run of a dark original, the 

 indicator

may blink and the copier stop, even though toner is left. The
copier will feed toner up to 2 minutes and then the START  key
indicator will light up. Press the START key to restart copying.

Summary of Contents for AR-207





















































































Reviews:

No comments

Related manuals for AR-207

Canon imageRUNNER 1750i Facsimile Manual preview
imageRUNNER 1750i
Brand: Canon Pages: 308

Brands by name

Popular brands

Load more brands