Sharp AR-162S Operation Manual Download

Page: 33 / 68

ST
A

TUS

INDICA

ORS

MISFEED REMOVAL

Misfeed removal

If the misfed paper is seen from this
side, proceed to “C. Misfeed in the
transport area”.

If paper is misfed here, proceed to
“B. Misfeed in the fusing area”.

If paper is misfed here, proceed to
“A. Misfeed in the paper feed area”.

Roller rotating knob

Check the misfeed location. Remove the misfed paper
following the instructions for each location in the
illustration below.

A. Misfeed in the paper feed area

Push gently on both sides of the front cover and open it.

Carefully remove the misfed paper. Turn the roller
rotating knob in the direction of the arrow to assist in
removing it.

The fusing unit is hot. Take care in removing paper.

Do not touch the photoconductive drum (green portion)
when removing the misfed paper. Doing so may
damage the drum and cause smudges on copies.

Close the front cover by pushing both sides with your
hands and then close the side cover by pressing the
handle on the cover.

●

The misfeed (

) indicator will go out.

When closing the covers, be sure to close the front
cover securely and then close the side cover. If the
covers are closed in the wrong order, the covers may
be damaged.

B. Misfeed in the fusing area

Push gently on both sides of the front cover and open it.

Summary of Contents for AR-162S





































































Search results

Summary of Contents for AR-162S

Reviews:

Related manuals for AR-162S

Brands by name

Popular brands

Sharp AR-162S, Operation Manual

Search results

Summary of Contents for AR-162S

Reviews:

Related manuals for AR-162S

Brands by name

Popular brands