Sharp AR-162S Operation Manual Download | Manualshive

Page: 28 / 68

background image

26

MAKING COPIES

1

Press the AUTO/MANUAL/PHOTO key to select the
PHOTO mode.

2

Press and hold down the AUTO/MANUAL/PHOTO key
for approximately 5 seconds.

●

The PHOTO indicator will go out and the AUTO indicator will begin
to blink.

●

One or two exposure indicators corresponding to the current auto-
matic exposure level will light up. The factory default setting is level
“3”.

3

Press the light (

) or dark(

) key to lighten or darken

the automatic exposure level as desired.

4

Press the AUTO/MANUAL/PHOTO key.

●

The AUTO indicator will stop blinking and will light up steadily.

●

This automatic exposure level will remain in effect until you change
it again by this procedure.

Automatic exposure adjustment

AUTOMATIC EXPOSURE ADJUSTMENT

The automatic exposure level can be adjusted to suit your copying needs.
This level is set for copying from the original table and copying from the
optional SPF respectively. To set the level for the optional SPF, place an
original in the document feeder tray and make sure that the SPF indicator
lights up before proceeding to step 1. To set the level for the original table,
ensure that the SPF indicator does not light up.

«
...
26
27
28
29
30
...
»

Summary of Contents for AR-162S





































































Reviews:

No comments

Related manuals for AR-162S

Brand: Oce Pages: 594

Brand: Ricoh Pages: 38

Brand: Triumph Adler Pages: 4

Brand: Triumph Adler Pages: 109

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands