Sharp AQUOS LC-70LE633U Service Manual Download Page 20 | Manualshive

Page: 20 / 60

background image

LC-70LE632U/633U

3 – 13

9. White balance adjustment

9.1. White balance adjustment (For details about the adjustment procedure, refer to “Kameyama Model Integrated Monitor
WB Adjustment Specification V1.92”.)

Adjustment

point

Adjustment conditions

Adjustment procedure

1

Setting

1) Set the unit to the following conditions.

AV MODE: [DYNAMIC]
Backlight: +16
Active Backlight: OFF
Aging Time: Min. 60 minutes

2) Connect the unit with the white balance adjustment jig.

2

Automatic
adjustment exe-
cution

[Command]
Process mode
KRSW0001
KKT10037

Setting
KY0F0000
0SDS0001
SBSL0016

Multi-point adjustment mode
MSET0001

Point 6
LEV60232
MG6G****
MG6B****
MG6R****

Point 5
LEV50194
MG5G****
MG5B****
MG5R****

Point 4
LEV40151
MG4G****
MG4B****
MG4R****

Point 3
LEV30107
MG3G****
MG3B****
MG3R****

Point 2
LEV20072
MG2G****
MG2B****
MG2R****

Point 1
LEV10045
MG1G****
MG1B****
MG1R****

Writing
MSET0003

[Adjustment procedure]
1) Send the “adjustment process” code using the remote control.
2) Set the point 6 to the specified gradation, specify the strongest color as the fixed

color, and adjust the RGB so that it becomes the standard value through negative
adjustment.

3) Set the point 5 to the specified gradation, set the G correction value (776 x G value of

point 6/928) (fractions rounded off) and adjust the RB so that it becomes the stan-
dard value.

4) Set the point 4 to the specified gradation, set the G correction value (604 x G value of

point 6/928) (fractions rounded off) and adjust the RB so that it becomes the standard
value.

5) Set the point 3 to the specified gradation, set the G correction value (428 x G value of

point 6/928) (fractions rounded off) and adjust the RB so that it becomes the standard
value.

6) Set the point 2 to the specified gradation, set the G correction value (288 x G value of

point 6/928) (fractions rounded off) and adjust the RB so that it becomes the standard
value.

7) Set the point 1 to the specified gradation, set the G correction value (180 x G value of

point 6/928) (fractions rounded off) and adjust the RB so that it becomes the standard
value.

8) Write the adjustment value by the MSET0003 command and turn off the AC power.
* RGB initial value of point 6: Set gradation 928
* RGB initial value of points 1 to 5: G correction value of each point

(At each point, make adjustment so that the remainder of the RGB adjustment value/
4 is equal.)

[Adjustment value]
* According to the “Standard settings” submitted by the Technical Department

[LC70LE632U] teaching set

«
...
18
19
20
21
22
...
»

Summary of Contents for AQUOS LC-70LE633U





























































Reviews:

No comments

Related manuals for AQUOS LC-70LE633U

Brand: Q.Bell Pages: 31

v-sense V8404 4K T10

Brand: i3TOUCH Pages: 44

FlexVision CTV-5060

Brand: Audiovox Pages: 3

Brand: TCL Pages: 53

Brand: Palsonic Pages: 30

Brand: Grundig Pages: 60

Brand: SoundMax Pages: 36

Brand: Naxa Pages: 18

SENTRY 2 SMS2047W

Brand: Zenith Pages: 32

Brand: Insignia Pages: 8

Brand: GE Pages: 42

Brand: RCA Pages: 34

Brand: RCA Pages: 88

Brand: Samsung Pages: 4

Brand: Samsung Pages: 6

Brand: Samsung Pages: 4

Brand: Samsung Pages: 36

Brand: Samsung Pages: 85

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands