7 - 6
LC-32WD1E/S/RU, LC-37WD1E/S/RU, LC-42WD1E/S/RU, and LC-32/37/42WT1E
D1103
Flash memory
M29W160ET90N6
The M29W160E is a 16 Mbit (2Mb x8 or 1Mb x16) non-volatile
memory that can be read, erased and reprogrammed. These
operations can be performed using a single low voltage (2.7 to
3.6V) supply. On power-up the memory defaults to its Read
mode where it can be read in the same way as a ROM or
EPROM.
D1107
Video filter
FMS6145MTC14
The FMS6145 Low-Cost Video Filter (LCVF) is intended to
replace passive LC filters and drivers with a low-cost integrated
device. Five 4th-order filters provide improved image quality
compared to typical 2nd or 3rd-order passive solutions. The
FMS6145 may be directly driven by a DC-coupled DAC output
or an AC-coupled signal. Internal diode clamps and bias
circuitry may be used if AC-coupled inputs are required.
D1207
Buffer
74LVC245APW
The 74LVC245A/74LVCH245A is an octal transceiver with non-
inverting 3-state bus compatible outputs in both send and
receive directions.
The 74LVC245A/74LVCH245A has an output enable (OE)
input for easy cascading and a send/receive (DIR) input for
direction control. OE controls the outputs so that the buses are
effectively isolated.
D1211
Power Switch
ST890CDR
The ST890 is a low voltage, P-Channel MOSFET power switch
intended for high side load switching applications. This switch
operates with inputs from 2.7V to 5.5V, making it ideal for both
3V and 5V systems. Internal current limiting circuitry protects
the input supply against overload. Thermal overload protection
limits power dissipation and junction temperatures. The
ST890’s maximum current limits is 1.2A. The current limit
through the switch is programed with a resistor from SET to
ground. The ST890 is available in SO-8 package. Main
applications are: PCMCIA slots, Access bus slots, Portable
equipment.
D1212
multiplexer
74LVC157APW
The 74LVC157A is a quad 2-input multiplexer which select four
bits of data from two sources under the control of a common
select input (S). The four outputs present the selected data in
the true (non-inverted) form. The enable input (E) is active
LOW. When pin E is HIGH, all of the outputs (1Y to 4Y) are
forced LOW regardless of all the other input conditions. Moving
the data from two groups of registers to four common output
buses is a common use of the 74LVC157A. The state of the
common data select input (S) determines the particular register
D1213
74LVC157APW
D1214
74LVC157APW
D1221
buffer
74LVC244APW
The 74LVC244A is a low voltage CMOS OCTAL BUS BUFFER
(3-STATE) fabricated with sub-micron silicon gate and double-
layer metal wiring C2MOS technology. It is ideal for 1.65 to 3.6
VCC operations and low power and low noise applications.
D1222
74LVC244APW
D1224
74LVC244APW
D1225
74LVC244APW
D1226
74LVC244APW
Digital Part (Voltage Regulation)
D1002
dc/dc converter
L6926
The device is dc-dc monolithic regulator specifically designed
to provide extremely high efficiency. L6926 supply voltage can
be as low as 2V allowing its use in single Li-ion cell supplied
applications. Output voltage can be selected by an external
divider down to 0.6V.
D1003
L6926
D1005
L6926
Ref No.
Name
Part Code
Description
