Sharp AL-1556 Operation Manual Download Page 105

Page: 105 / 116

MATERIAL SAFETY DATA SHEET

Data Revised: Jul .31, 2002
Data Issued:

Jun. 1, 1998

MSDS NO. F-30831

103

3. HAZARDS IDENTIFICATION

Most Important Hazards and Effects of the Products

Human Health Effects :There are no anticipated carcinogenic effects from exposure based on

animal tests performed using toner. When used as intended according to
instructions, studies do not indicate any symptoms of fibrosis will occur.

Environmental Effects :No data are available.

Specific hazards

Dust explosion (like most finely divided organic powders)

Directive 1999/45/EC(Europe) :

Not classified as dangerous

4. FIRST-AID MEASURES

Route(s) of Entry :Inhalation?

Skin?

Ingestion?

Yes

Possible but very unusual.

Inhalation

:Remove to fresh air. If symptoms occur, consult medical personnel.

Skin Contact

:Wash with soap and water for 15 minutes or until particle is removed.

If irritation does occur, consult medical personnel.

Eye Contact

:flush eyes immediately with water for 15 minutes. If irritation does occur,

consult medical personnel.

Ingestion

:Rinse with water and drink several glasses of water . If irritation or discomfort

does occur, consult medical personnel.

5. FIRE -FIGHTING MEASURES

Extinguishing Media

:water, CO

, foam and dry chemicals

Special Fire fighting Procedures

:None

Fire and Explosion Hazards

:Toner material, like most finely divided organic powders, it

may form an explosive mixture.

6. ACCIDENTAL RELEASE MEASURES

Personal Precautions

:None

Environmental Precautions

:None

Methods for Cleaning Up

:Wipe off with paper or cloth. Do not use vacuum cleaner when a

large amount is released. It, like most finely divided organic
powders, is capable of creating a dust explosion.

7. HANDLING AND STORAGE

Handling

Technical Measures :None
Precautions

:None

Safe Handling Advice :Use of a dust mask is recommended when handling a large quantity of

toner or during long term exposure, as with any non-toxic dust. Try not
to disperse the particles.

Storage

Technical Measures :None
Storage Conditions

:Keep container closed and Store in a cool and dry place.

Keep out of the reach of children.

Incompatible Products:None

8. EXPOSURE CONTROL / PERSONAL PROTECTION

Engineering Measures

Ventilation

:None required with intended use.

Exposure limit values

OSHA-PEL (USA)

:15m

(Total Dust) , 5m

(Respirable Dust)

ACGIH-TLV (USA)

:10m

(Total Dust) , 3m

(Respirable Dust)

Page: 2/4

Summary of Contents for AL-1556





















































































































Search results

Summary of Contents for AL-1556

Reviews:

Related manuals for AL-1556

Brands by name

Popular brands

Sharp AL-1556, Operation Manual

Search results

Summary of Contents for AL-1556

Reviews:

Related manuals for AL-1556

Brands by name

Popular brands