Shark SGP-3020 Operator'S Manual Download Page 3

Shark SGP  •  97-6132  •  REV. 4/07

3

  PRESSURE 

W

ASHER     

OPERA

TOR’S MANU

AL

  

INTRODUCTION & IMPORTANT SAfETy INfORMATION

Thank you for purchasing this Pressure Washer.
We  reserve  the  right  to  make  changes  at  any  time 
without incurring any obligation.

Owner/User Responsibility:

The  owner  and/or  user  must  have  an  understand-
ing of the manufacturer’s operating instructions and 
warnings before using this pressure washer. Warning 
information  should  be  emphasized  and  understood. 
If the operator is not fluent in English, the manufac-
turer’s instructions and warnings shall be read to and 
discussed with the operator in the operator’s native 
language by the purchaser/owner, making sure that 
the operator comprehends its contents.
Owner and/or user must study and maintain for future 
reference the manufacturers’ instructions.
The  operator  must  know  how  to  stop  the  machine 
quickly and understand the operation of all controls. 
Never  permit  anyone  to  operate  the  engine  without 
proper instructions.

This manual should be considered a permanent 

part of the machine and should remain with it if 
machine is resold.
When ordering parts, please specify model and 
serial number. Use only identical replacement 
parts.
This machine is to be used only by trained op-
erators.

IMPORTANT SAfETy 

INfORMATION

READ OPERATOR’S 

MANUAL ThOROUGhLy 

PRIOR TO USE.

WARNING: To reduce the risk of 

injury,  read  operating  instruc-
tions carefully before using.

  1.  Read  the  owner's  manual 

thoroughly.  Failure  to  follow 
instructions could cause mal-
function  of  the  machine  and 
result in death, serious bodily 
injury  and/or  property  dam-
age.

  2.  Know how to stop the machine and bleed pressure 

quickly. Be thoroughly familiar with the controls.

  3.  Stay alert — watch what you are doing.
 

WARNING

kEEP WATER 

SPRAy AWAy fROM 

ELECTRICAL WIRING.

WARNING: Keep wand, hose, and 

water  spray  away  from  electric 
wiring or fatal electric shock may 
result.

4.    All  installations  must  comply 

with  local  codes.  Contact 
your  electrician,  plumber, 
utility company or the selling 
distributor for specific details.

WARNING

EAR PROTECTION 

MUST bE WORN

WARNING: This machine exceeds 

85 db appropriate ear protection 
must be worn.

WARNING

USE PROTECTIvE  

EyE WEAR 

AND CLOThING  

WhEN OPERATING 

ThIS EqUIPMENT.

WARNING: High pressure spray 

can cause paint chips or other 
particles  to  become  airborne 
and fly at high speeds. To avoid 
personal  injury,  eye,  hand  and 
foot  safety  devices  must  be 
worn.

  5.   Eye, hand, and foot protection 

must be worn when using this 
equipment.

  6.  Keep operating area clear of all persons.
 

RISk Of ExPLOSION: 

OPERATE ONLy WhERE 

OPEN fLAME OR TORCh 

IS PERMITTED

WARNING

WARNING:  Flammable  liquids 

can create fumes which can ig-
nite,  causing  property  damage 
or severe injury.
WARNING:  Risk  of  explosion 
—  Operate  only  where  open 
flame or torch is permitted.

 

RISk Of fIRE.  

DO NOT ADD fUEL 

WhEN OPERATING 

MAChINE.

WARNING

WARNING: Risk of fire — Do not 

add  fuel  when  the  product  is 
operating or still hot. 
WARNING: Do not use gasoline 
crankcase  draining  or  oil  con-
taining  gasoline,  solvents  or 
alcohol. Doing so will result in 
fire and/or explosion.
WARNING: Risk of fire — Do not 

Spray flammable liquids. 

  7.  Allow engine to cool for 1-2 minutes before refu-

eling. If any fuel is spilled, make sure the area is 
dry  before  testing  the  spark  plug  or  starting  the 
engine. (Fire and/or explosion may occur if this is 
not done.)

    Gasoline engines on mobile or portable equipment 

shall be refueled:

    a.  outdoors;
    b.  with the engine on the equipment stopped;
    c.  with  no  source  of  ignition  within  10  feet  of  

 

the dispensing point; and

    d.  with an allowance made for expansion of the  

 

fuel should the equipment be exposed to a  

 

higher ambient temperature.

Summary of Contents for SGP-3020











































Reviews: