Shark Pressure Washers EEC-353007C Operator'S Manual Download Page 4

9.801-296.0฀฀•฀฀Shark฀฀•฀฀Rev.฀11/12

OPERA

T

OR’S MANU

AL

 

PRESSURE 

W

ASHER  

4

WARNING: High pressure spray 
can cause paint chips or other 
particles to become airborne 
and fly at high speeds.

11.   Eye, hand and foot safety 

devices must be worn when 
using this equipment.

12.   Machines with spray guns 

should not be operated with

 

the spray gun in the off posi-

tion for extended periods of time as this may cause 
damage to the pump. 

 13.  Protect from freezing.

 14. Protect discharge hose from vehicle traffic and 

sharp objects.

 15.  To prevent a serious injury, be certain quick coupler 

on discharge hose has locked before using pres-
sure washer.

 16.  Before disconnecting discharge hose from hot wa-

ter outlet, disconnect power supply, open spray gun 
to relieve back pressure in hose and use protective 
gloves.

 17. Do not allow acids, caustic or abrasive fluids to 

pass through the pump.

 18. Inlet water supply must be cold and clean fresh 

water.

 19.  The best insurance against an accident is precau-

tion and knowledge of the machine.

 20.  Shark will not be liable for any changes made to 

our standard machines, or any components not 
purchased from Shark.

 21. To reduce the risk of injury, close supervision is 

necessary when a machine is used near children. 
Do not allow children

 

to operate the pressure 

washer. 

This machine must be attended during 

operation.

 22. Do not overreach or stand on unstable support. 

Keep good footing and balance at all times.

 23. Follow the maintenance instructions specified in 

the manual.

 24. When making repairs disconnect from electrical 

source.

 25.  Do not operate this product when fatigued or under 

the influence of alcohol or drugs. Keep operating 
area clear of all persons.

26. 

WARNING: Do not use below garage floor or 

grade level.

PRE-OPERATION CHECK 

   

  

 

  Heat module water level

    

    Pump oil (SAE 30W non-detergent oil)

    

Cold฀water฀supply฀(6฀gpm฀•฀5/8"฀•฀20฀psi)

    

 

Proper power supply

  

   

Hose, wand, nozzles (nozzle sizes per serial  

 plate)

    

 

Water filter (intact, non restrictive)

  

   

Read installation and operation instructions 

Follow the maintenance instructions 
specified in the manual.

IMPORTANT SAFETY INFORMATION

WARNING

PROTECTIVE 

EYE WEAR AND 

CLOTHING 

MUST BE WORN.

Summary of Contents for EEC-353007C



















Reviews: