21
Giotto Spot 400 CMY rel.1.00
Control Microcomputer
GB
3.11 Remote control of lamp ignition
Operators can decide if the ignition of the Giotto's lamp is to be controlled from a lighting console or be automatic.
To access this function, proceed as follows:
1.
Connect Giotto Spot to the power supply, wait till it has completed reset operations and “DMX
signal” appears on the display.
2.
Use the UP/DOWN keys to find the “LMP_ctr” menu.
3.
Press ENTER to confirm. The message on the display will start to flash.
4.
Use the UP/DOWN keys to select the required option.
5.
Press ENTER to confirm the modifications.
3.12 Remote control of fixture reset
Using this menu, it's possible to decide whether to reset the fixture via remote control or not.
To enable this function , proceed as follows:
1.
Connect Giotto Spot to the power supply, wait till it has completed reset operations and “DMX signal” appears on
the display.
2.
Use the UP/DOWN keys to find the “RST_ctr” menu.
3.
Press ENTER to confirm. The message on the display will start to flash.
4.
Use the UP/DOWN keys to select the required option.
5.
Press ENTER to confirm the changes.
3.13 Control of the acceleration of movement speed
Movement can be optimized by changing the speed (SPEED) and acceleration (ACCEL) parameters, obtaining
smooth fast or slow movements as required.
To optimize movement, proceed as follows:
1.
Connect Giotto Spot to the power supply, wait till it has completed reset operations and “DMX signal” appears on
the display.
2.
Use the UP/DOWN keys to find the “Speed” or “Accel” menu.
3.
Press ENTER to confirm. The message on the display will start to flash.
4.
Use the UP/DOWN keys to select the required option.
5.
Press ENTER to confirm the changes.
3.14 Display brightness
Operators can select one of the brightness levels available for the Giotto display, which can be standard or very
low. This option is intended for theatre and television use, where excessive brightness can be troublesome.
To change display brightness, proceed as follows:
1.
Connect Giotto Spot to the power supply, wait till it has completed reset operations and “DMX signal” appears on
the display.
2.
Use the UP/DOWN keys to find the “Bright” menu.
3.
Press ENTER to confirm. The message on the display will start to flash.
4.
Use the UP/DOWN keys to select the required option from those available.
5.
Press ENTER to confirm the modifications.
3.15 Display reading position
When the fixture is mounted "upside down" on a structure, operators can turn the display through 180°, thus grea-
tly facilitating the reading of the menus on the display.
To change the reading position, proceed as follows:
1.
Connect Giotto Spot to the power supply, wait till it has completed reset operations and “DMX signal” appears on
the display.
2.
Use the UP/DOWN keys to find the “Dspl Flip” menu
3.
Press ENTER to confirm. The message on the display will start to flash.
4.
Use the UP/DOWN keys to select the required option.
5.
Press ENTER to confirm the modifications.
3.16 dmx dly
This allows to set the for how many seconds the fixture's last operating settings are maintained should there be no
DMX signal. This function is indispensable in those cases in which there is an accidental DMX failure.
To set the required time, proceed as follows:
1.
Connect Giotto Spot to the power supply, wait till it has completed reset operations and “DMX signal” appears on
the display.
2.
Use the UP/DOWN to find the “DMXDLY” menu.
3.
Press ENTER to confirm. The message on the display will start to flash.
4.
Use the UP/DOWN keys to select the required time.
5.
Press ENTER to confirm changes.
DMXdly=20
DsplFlip
Bright=40%
Accel=Fast
Speed=100%
RST_st=DS
Lmp_ctr=DS
