background image

10

© 1998 SGC Inc

6.1.1 DESK TOP INSTALLATION

A Flip Front Foot is supplied with the radio.

This foot can be flipped up to raise the front of the radio 3 inches
above the desk level.  Additional front flip feet can be ordered sep-
arately, catalog number 05-43.

6.1.2 DESK OR BASE MOUNTING (option 05-42)

To mount the SG-2020 in a secure installation, use the optional
mounting plate in the  transverse  or longitudinal position a s
described below:

A.  Remove 3 screws in the bottom of the chassis.
B.  Line up the mounting plate so the 3 holes match the

screw holes in the chassis.

C.  Re-install the 3 pan head screws provided with the plate

to secure the  radio to the mounting plate.

D.  Secure the radio to a flat surface using four self-tapping 

wood or sheet metal screws.

6.2

MOBILE 

6.2.1 POWER CONNECTION

(Negative Ground vehicles only)

The DC power cable for mobile installation should be made with
AWG #12 stranded copper wire.  Please review all power supply
considerations throughout this manual and apply all recommenda-

SGC Inc. SGC Building, 13737 S.E. 26th St.  Bellevue, WA. 98005 USA

P.O.Box  3526, 98009  Fax: 425-746-6384 or 746-7173 Tel:  425- 746-6310 or 1-800-259 7331

E-mail: [email protected]   Web site: http://www.sgcworld.com

Summary of Contents for SG-2020 TEST DOCUMENT
































































































Reviews: