background image

EC DECLARATION OF CONFORMITY 

 

 
 

 
We,  

SGB Sicherungsgerätebau GmbH 
Hofstraße 10 

D- 57076 Siegen 

hereby declare in sole responsibility that the leakage probes 

DL.., DLR-P.. 

 

comply with the essential requirements of the EC directives listed below. 

 

This declaration shall lose its validity if the device is modified without consulting us. 

Number / short title

 

Satisfied regulations

 

2004/108/EC 
EMC Directive

 

EN 61 000-6-3: 2007 
EN 61 000-6-2: 2005 
EN 61 000-3-2: 2006 
EN 61 000-3-3: 1995 + A1: 2001 + A2: 2005 

2006/95/EC 
Low Voltage Directive

 

EN 60 335-1: 2007 
EN 61 010-1: 2001 
EN 60 730-1: 2005 

89/106/EEC 
Construction Products 
Directive 
93/68/EEC 

EN 13 160-1-2: Approved body: TÜV-Nord, Hamburg

 

94/9 EEC 
Equipment in Potentially 
Explosive Atmospheres

 

The leak detector with its pneumatic parts may be connected to 
spaces (interstitial spaces of tanks / pipelines / fittings) which are 
required for category 3 devices. The following documents were 
used: 
EN 1127-1: 2007 
EN 60 079-10: 2003 
EN 13 160-1-2: 2003 
EN 13463-1: 2001 
The ignition hazard analysis did not result in any additional 
hazards.

 

 

Compliance is declared by 

 

 

Martin Hücking 
(Technical Director) 

L:\ÜBERSETZUNGEN\DOKUMENTATIONEN\ENGLISCH\DL\15-1-Declaration DL..-DLR-P...DOC 

Last updated: January 2009

 

37/38

Summary of Contents for DLR-P







































Reviews: