SFA SANICOM 1 Installation Instructions Manual Download Page 6

Page: 6 / 32

WARNING NOTICE

SANICOM

is a lifting pump for wastewater used in com-

mercial applications (restaurants, hairdressing salons, the

catering industry etc.). The unit operates automatically, has

a high performance level, and is safe and reliable, provided

all the rules for installation and maintenance in this notice

are strictly followed.

Especially those indicated by:

» Failure to comply with this instruction could endanger

the safety of persons,

» Indication that a risk of electrical

origin exists,

» Electrical installation must be carried out by a

professional electrician.

ATTENTION

» Failure to comply with this instruction could

endanger the safe functioning of the apparatus.
For any additional information, please contact our customer

service department.

HOW IT WORKS

SANICOM

contains 1 pump. The tank is equipped with a

sensor tube which controls the automatic activation of the

motor when waste enters the unit.

As soon as the waste enters the tank, the pump starts.

LIST OF PARTS SUPPLIED

DIMENSIONS

SANICOM

1 TECHNICAL DATA AND APPLICATION

>>$!=+"!)'

!'D:H*+:A!'@&+=A!',H
/!:A*+:A,.).:A)*,.J
).+"AJ

Type

P95

Maximum vertical pumping height

10 m

Voltage

220 – 240 V

Frequency

50 Hz

Maximum power consumption

1300 W

Maximum current consumption

6 A

Electrical class

Protection index

IP44

Max temp with intermittent functioning

90°

Net weight

10 kg

* In the case of bath or shower tray, make sure the waste

traps are raised 19 cm above floor level.

1. All applications other than those described in

this notice are prohibited.

2. Do not exceed an incoming flow rate greater

than 80% of the flow rate stated on the design

curve

in any of the apparatus.

PERFORMANCE CURVES

VERTICAL/HORIZONTAL PUMPING

INSTALLATION

The pump has securing devices, preventing it from turning

or moving.

1- Warning: The space in which

SANICOM

is installed must

be large enough to leave at least 600mm around the unit
for easy maintenance. This space must be well lit, ventila-
ted, and must never be immersed in water and must be
protected from frost.

2- Isolation valves should be fitted to the inlet pipework and

discharge pipework to isolate the unit in case of the need
for service.

3- This evacuation pipe must be designed so as to prevent

back-flow from the sewers.

CONNECTION TO SIDE INLETS

Use the flexible inlet connector

for side input connections.

Using a metalwork saw, saw
the desired input point, remove any burrs and then fix the
flexible inlet connector with the jubilee clip

In the case of an installation for drainage of

greasy wastes allow for a grease trap in front of each input
point.
Connection to the inlet can be made using a DN40
or DN50 pipe. To make a DN50 connection, cut off the end
of sleeve

beforehand.

To connect bathtub (or shower), make sure the waste
trap height is raised by at least 19 cm above floor level.
Connection must be made using 40 mm or 50 mm diameter
pipework, with minimum slope of 1%.

The disposal of waste from the

SANICOM

can discharged

through a 32 mm diameter copper or plastic pipes (or PVC,
ABS, etc.).
Horizontal discharge pipework should maintain a 2,5% fall
(1cm/M) to the soil and vent pipe. If a vertical rise is
required, this must be installed at the start of the run,
before the horizontal section.

+D,=+.,"A+""A,/!:=A+.@,<+$<,;$+>;+=,:"A,/!.,=I
"!)');;$)*S

If the end of the discharge pipework is much lower than the
unit, install a riser pipe about 80mm long from the highest
point of the discharge run and fit an air admittance pipe on
top (capable of withstanding at least 15psi pressure.) to
break the syphon.
End the outlet pipe at the waste stack.

be sure to fit hoop

Allow for a drain-off point at the bottom of the rising

waste pipe. Ensure that the unit is easily accessible for pos-
sible maintenance.

ELECTRICAL CONNECTION

The electrical installation should be carried by a qualified
person.
All wiring must conform to BS7671, 1992 requirements for
electrical installation. The unit requires a 220/240 V single
phase AC 50 Hz supply (UK specification). Do not connect
the unit to a conventional plug and socket. The unit should be
connected to a fully earthed electrical supply (class 1). It must
be wired into an unswitched fused fixed wiring connector
protected by a 10 amp fuse and a residual current detector
(30 mA). This connection must be used exclusively for
supplying the

SANICOM

unit.

The wires in the mains lead are coloured in accordance with
the following code:

Brown

Live

Blue

Neutral

Green/Yellow

Earth

: Ensure the electricity is turned OFF at the main

switch board before wiring to connector. All work on cable,
pressure chamber and motor should only be carried out by a
qualified

servicing agent, as special tools are