SFA MAXLITE, Installation Instructions Manual

Page: 14 / 14

4
12 FAULT FINDING
In most cases, any inconsistencies in the operation of the unit will be minor and easy recti-
fied. Please refer to the chart below. If the problem cannot be easily remedied thanks to this
chart, please call our SFA Service organisation or go to a SFA-approved technician.
FAULT OBSERVED PROBABLE CAUSES TROUBLESHOOTING
• The motor does not work • No electricity supply • Check the control switch
• Check the electrical connections
• Check the power source.
• The motor works but there is no
water inlet for flushing
• The inlet pipe filter is clogged
• The water inlet pipe is
pinched
• The through-hull valve is
closed
• The pump is unprimed
• The water injection nozzle /
check valve is clogged
• The switch is wrongly
wired up
• Clean the filter
• Check the pipes
• Check the through-hull valve
• Check the pump and the flexible
blade turbine
• If necessary change the turbine
• Check the water injection nozzle
• Check the check valve
• Check the connection of the
cables.
• The motor works but there is
no outlet
• The outlet is clogged
• The outlet is too high
• The through-hull valve is
closed
• There is no water in the bowl
• The switch is wrongly wired up
• Dismantle and clean the outlet
• Change the outlet
• Check the pipe routing
• Check the through-hull valve
• Add water to the bowl
• Check the connection of the
cables.
• The motor runs with a rattling
noise
• A hard foreign body has fallen
into the bowl
• Cut the power supply to the
motor.
• Close the through-hull valves
• Remove the motor unit
• Use a hook to remove all
matter that could interfere with the
rotation of the shredder
• Use a tool to rotate the turbine in
both directions until it turns
freely
• Reconnect the power supply to
the motor. and press the «Pump
out» key to check the operation of
the appliance
• Re-open the through-hull valves
• If the macerator is still jammed
we advise you to contact our
ervice department who will be able
to advise you or direct you to one
of our service stations nearest to
your area.
DISCONNECT THE ELECTRICAL POWER SUPPLY,
BEFORE ATTEMPTING ANY WORK ON THE UNIT.
UK
13
GUARANTEE
2 years guarantee from date of purchase,
subject to correct installation and correct use:
disposal of toilet papers and fecal matter only.
Guarantee is limited to replacement or service
of the defective spare parts, and any indemnity
or claim for damages will not be included.
Freight and packing costs, travel expenses
are not included in the guarantee. It does not
cover any normal deterioration of the material
over time, any external deterioration or accident,
incorrect disposal of sanitary products. Any mo-
dification without prior notice will not be under
guarantee. Fixing, modification, or replacement
11
WINTERING
In the event of a long period without use, rinse
the bowl and carry out several flushing cycles
with the fresh water and close through-hull val-
ves.
of parts without our agreement will not be gua-
ranted, and will invalidate it. Our liability is solely
for the product itself.
Guarantee starts from date of purchase we may
request a copy of the invoice to validate the pur-
chase date.
9 ELECTRICAL
CONNECTION
Advice for wiring up the Sanimarin Maxlite:
The maximum recommended voltage drop is
5% or 0.6V for a supply voltage of 12V, and
1.2V for a supply voltage of 24V;
In the event of prolonged absence of supply or
long absence, cut off the water and electricity
supplies to the Maxlite.
Electricity consumption per second:
12V : 0.007 Ah
24V : 0.004 Ah
Current consumption / Fuses:
12V : 300 W / 25 A
24V : 360 W / 15 A
Electric diameter wire:
12V (300 W)
1.5mm² = 1M max
2.5mm² = 2M max
4mm² = 3M max
6mm² = 4,3M max
24V (360W)
1.5mm² = 3,5M max
2.5mm² = 6M max
4mm² = 9,5M max
6mm² = 14M max
10
Cleaning / descaling
For cleaning, use normal sanitary products.
CAUTION:
• Do not use aggressive chemicals (such as
acetone, pure bleach, etc.) that could da-
mage the material of the bowl.
• Use a suitable standard toilet brush; do
not use scouring or abrasive pads.