background image

5

4

2-2. Connecting the Cables

You can connect up the cables required for printing to the printer. 
They all connect to the connector panel on the back of the printer, which is shown below :

Before connecting any of the cables, make sure that both the printer and the computer are turned off.

2-1. Unpacking

Your printer box should include these items. If any items are damaged or missing, please contact your 
dealer for assistance.

                                                   

 

The Printer   

                       CD 

 

            Roll Paper

    

     

 

           

                           

 Adaptor(option) 

                                       

 Interface Cable(optional) 

            

  

  

2. Setting Up the Printer

For connection to a

host computer.

For connection to a

host computer.

For connection to a

host computer.

Connects to peripheral units

such as cash drawers, etc.

Do not connect this to

a telephone.

INTERFACE CONNECTOR
(ETHERNET)

INTERFACE CONNECTOR(SERIAL)

INTERFACE CONNECTOR(USB)

PERIPHERAL DRIVE CONNECTOR

POWER CONNECTOR

For connection of the 

AC adapter.

Never unplug the AC 

adapter while the 

printer is on.

Summary of Contents for SLK-T21EB Series













Reviews: