manualshive.com logo in svg

SEW-Eurodrive DH 21B Series, Manual, Page: 66 / 92

Share
Download
SEW-Eurodrive DH 21B Series Manual Download Page 66

8

Operation

DHF21B/41B controller

Manual – DHE/DHF/DHR21B (standard) and DHE/DHF/DHR41B (advanced)

66

No.

Name

Function

LED 13

BUS OFF

The two-color LEDs 13 – 16 indicate the
current state of the fieldbus and the
DeviceNet

TM

 interface.

LED 14

Bit strobe I/O

LED 15

Polled I/O

LED 16

MOD/NET

LED 17

PROFIBUS fault

Status of PROFIBUS electronics

LED 18

RUN PROFIBUS

Status of PROFIBUS communication

8.2.1

LEDs in PROFIBUS mode

LED "L17" (PROFIBUS fault)

LED  "L17"  (PROFIBUS  fault)  indicates  that  communication  via  the  PROFIBUS  inter-
face is working properly.

Status LED

Possible cause

Measure

Off

The MOVI‑PLC

®

 advanced controller is

exchanging data with DP master (data
exchange state).

–

Red

•

Connection to the DP master has
failed.

•

The MOVI‑PLC

®

 advanced control-

ler does not detect a PROFIBUS
baud rate.

•

Bus interruption.

•

DP master not in operation.

•

Check the PROFIBUS DP connec-
tion of the device.

•

Check the configuration of the DP
master.

•

Check all the cables in the
PROFIBUS DP network.

Flashing red with 1 Hz

•

The MOVI‑PLC

®

 advanced control-

ler has detected the baud rate, but
is not addressed by DP master.

•

The MOVI‑PLC

®

 advanced control-

ler was either not configured in the
DP master or has been configured
incorrectly.

•

Check and correct the PROFIBUS
address set in the MOVI‑PLC

®

 ad-

vanced controller and in the config-
uration software of the DP master.

•

Check and correct the configura-
tion of the DP master.

•

Use the GSD file 

SEW_6007.GSD

with the designation 

MOVI‑PLC

 for

configuration.

LED "L18" (RUN PROFIBUS)

LED "L18" (RUN PROFIBUS) indicates that the PROFIBUS electronics (hardware) is
working properly.

Status LED

Possible cause

Measure

Green

PROFIBUS hardware is OK.

–

Green, flashing with 1 Hz

The PROFIBUS station address set
on the DIP switches is more than
125. Station addresses >125 are not
permitted. The system does not start
up. The maximum permitted station
address is 125.

1. Check and correct the PROFIBUS

station address on the DIP switches.

2. Switch on all inverters again. The

modified PROFIBUS station address
will only take effect after a restart.

22900055/EN – 08/2016

Summary of Contents for DH 21B Series





























































































Reviews:

No comments