manualshive.com logo in svg

SEW-Eurodrive DH 21B Series, Manual, Page: 59 / 92

Share
Download
SEW-Eurodrive DH 21B Series Manual Download Page 59

7

Project planning and startup with MOVITOOLS

®

 MotionStudio

Startup of the fieldbus at the DHR21B/41B controller

Manual – DHE/DHF/DHR21B (standard) and DHE/DHF/DHR41B (advanced)

59

Initial startup

If  the  EtherNet/IP  and  Modbus/TCP  protocol  is  set  using  the  DIP  switch,  the  default
protocol  for  the  DHR21B/41B  option  will  be  "DHCP"  (

D

ynamic 

H

ost 

C

onfiguration

P

rotocol). This means that the option card expects its IP address parameters from a

DHCP server.

INFORMATION

There is a free DHCP server available on the Rockwell Automation homepage. The
tool is known as "BOOTP Utility" and can be downloaded from the following website:
http://www.ab.com/networks/bootp.html.

Once the DHCP server has been configured and the settings have been made for the
subnet mask and the standard gateway, the DHR21B/41B option card must be inser-
ted  in  the  assignment  list  of  the  DHCP  server.  In  doing  so,  the  MAC  ID  of  the
DHR21B/41B option card is allocated a valid IP address.

INFORMATION

The  configured  IP  address  parameters  are  adopted  permanently  by  the  parameter
set when DHCP is deactivated after the IP address has been assigned.

Changing IP address parameters after initial startup

If the DHR21B/41B option card was started using a valid IP address, you can also ac-
cess the IP address parameters via the Ethernet interface.

You can change the IP address parameters via Ethernet by one of the following meth-
ods:

•

With the MOVITOOLS

®

 MotionStudio engineering software

•

Using the EtherNet/IP

TM

 TCP/IP interface object (see chapter "EtherNet/IP CIP ob-

ject directory")

•

With the SEW Address Editor

You  can  also  change  IP  address  parameters  via  the  other  interface  of  the
DHR21B/41B option card.

If  the  IP  address  parameters  of  the  DHR21B/41B  option  card  are  assigned  via  a
DHCP  server,  you  can  only  change  the  parameters  by  adjusting  the  settings  of  the
DHCP server.

The methods listed above for changing the IP address parameters only come into ef-
fect once the supply voltage (DC 24 V) has been switched off and back on again.

Deactivating/activating DHCP

The type of IP address assignment is determined by the setting of the attribute 

Config-

uration Control 

of the EtherNet/IP

TM

 TCP/IP interface object. The value is displayed or

changed in the parameter 

P785 DHCP/Startup Configuration

.

•

"Stored IP parameters" setting

The stored IP address parameters are used.

•

"DHCP" setting

The IP address parameters are requested by a DHCP server.

If you use the DHCP server from Rockwell Automation, you can activate or deac-
tivate  the  DHCP  by  clicking  a  button.  In  this  case,  an  EtherNet/IP

TM

  telegram  is

sent to the TCP/IP interface object of the station that is being addressed.

22900055/EN – 08/2016

Summary of Contents for DH 21B Series





























































































Reviews:

No comments