Seresco CLASSIC NE Series Operation And Maintenance Manual Download Page 30

W – Warranty 

OMM.W.S.ZZ.02

 

W-

1

 

March

 2019

 

Warranty 

General Policy 

This warranty applies to the original equipment owner and is not transferable. Seresco Technologies Inc. warrants 
as set forth and for the time periods shown below that it will furnish, through a Seresco Technologies Inc. 
authorized installing contractor or service organization, a new or rebuilt part for a factory installed part which has 
failed because of defect in workmanship or material. 

Warranty Void Unless Registered 

Warranty is void unless, upon start-up of the equipment, the “Warranty Registration and Start-up Report” is 
completed and sent to the factory within one week of initial start-up. This report will also register the compressor 
warranty with the compressor manufacturer. 

Initial 90-day Warranty 

During the first 90 days from initial start-up and prior to the completion of the 24

th

 month from date of shipment, 

whichever comes first and subject to prior written approval from the factory, Seresco Technologies Inc. will 
provide and/or reimburse the required labour, materials, and shipping and handling costs incurred in the 
replacement or repair of a factory installed defective part. Only the labour required to replace the defective part is 
warrantied – travel time, diagnostic time, per diems, truck charges, etc. are not covered under this warranty. 

WebSentry Conditional One Year Extended Labour Warranty 

The initial 90-day labour warranty shall be extended for a total of 12 months from initial start-up and prior to the 
completion of the 24

th

 month from date of shipment, whichever comes first and subject to prior written approval 

from the factory. The provided equipment must be connected and communicating to Seresco's WebSentry online 
control and monitoring service for the entire term of the warranty extension. Seresco Technologies Inc. will 
provide and/or reimburse the required labour, materials, and shipping and handling costs incurred in the 
replacement or repair of a factory installed defective part. Only the labour required to replace the defective part is 
under warranty – travel time, diagnostic time, per diems, truck charges, etc. are not covered under this warranty. 

Two Year Parts Warranty 

If any factory installed part supplied by Seresco Technologies Inc. fails because of a defect in workmanship or 
material prior to the completion of the 24

th

 month from date of shipment, Seresco Technologies Inc. will furnish a 

new or rebuilt part F.O.B. factory. No labour reimbursement will be made for expenses incurred in making field 
adjustments or parts replacement outside the 

Initial 90-day Warranty

. Seresco Technologies Inc. reserves the right 

to have the defective part returned to the factory in order to determine the warranty applicability. Parts shipping 
and handling costs (to and from the factory) are not covered outside of the 

Initial 90-day Warranty

Summary of Contents for CLASSIC NE Series


































Reviews: