Sequential Prophet X, User Manual

Page: 71 / 88

126 127 Sequential Prophet X User’s Guide Global Settings
Global Settings
• With
breath cc
2
selected, an expression pedal connected to the
filter
jack will control whatever parameter is routed to the modulation source
“Breath” within the modulation matrix.
• With
foot cc
4
selected, an expression pedal connected to the
filter
jack will control whatever parameter is routed to the modulation source
“Foot” within the modulation matrix.
• With
exp cc
11
selected, an expression pedal connected to the
filter
jack will control whatever parameter is routed to the modulation source
“Expression” within the modulation matrix.
• With
lpf full
selected, an expression pedal connected to the
filter
jack
will control filter cutoff frequency within its full range of 0-164 (fully
closed to fully open).
• With
lpf half
selected, an expression pedal connected to the
filter
jack
will control filter cutoff frequency within half of its range (fully closed
to half open).
22 . Seq Pedal Mode: Normal, Trigger, Gate, T-G—
Selects the mode
for the rear-panel
sequencer
jack. This jack requires a unipolar signal.
Connecting a bipolar signal can damage this input.
• With
normal
selected, a footswitch will start sequencer playback.
• With
trig
selected, an audio signal connected to the
sequencer
jack
will step the sequencer when the sequencer’s
play
button is on.
• With
gate
selected, an audio signal connected to the
sequencer
jack will trigger and gate the envelopes while you hold a note or
chord. Additionally, turning on the sequencer or arpeggiator will add
sequencer or arpeggiator playback — but controlled by the Prophet X’s
clock
bpm
and
value
settings and not the audio trigger.
• With
t
-
g
(
trigger
+
gate
) selected, an audio signal connected to the
sequencer
jack will trigger and gate the envelopes while you hold a
note or chord. Additionally, pressing the sequencer’s
play
button will
also add synchronized sequencer playback.
23 . Sustain Polarity: Normal, Reversed—
There are two types of
momentary footswitches, normally open and normally closed. Either
type can be used with the Sustain switch input. This setting allows you
to accommodate both models in case yours behaves in a way that is
the opposite of what you expect due to its polarity. (Sustain is on until
the footswitch is pressed and then it turns off, which is the opposite of
the expected behavior.) Connect your pedal and choose the appropriate
setting based on its behavior.
24 . Sustain Arp: Arp hold, Sustain— Sets the function for the
sustain
pedal input the rear of the synthesizer. Selecting
arp hold
and pressing
the sustain pedal causes the arpeggiator to hold the current arpeggio as
if you had pressed the hold button on the front panel. Selecting
sustain
chooses normal sustain pedal operation.
25 . Calibrate Wheels — Calibrates the Pitch and Mod wheels.
26 . Calibrate Sliders — Calibrates touch slider 1 and touch slider 2.
27 . Basic Program —
Loads a basic template program.
28 . Calibrate Filters —
Calibrates the filters. You shouldn’t need to do
this under normal circumstances since the filters are calibrated at the
factory and generally don’t require re-calibration or re-tuning.
29 . Update Application — Updates the Prophet X operating system. To
do this you must download the new OS to a properly formatted USB
flash drive/thumb drive (see
“Formatting a USB Flash Drive” on page
120) then connect the drive to the
sample import
port on the rear of the
Prophet X.
30 . Update Library: Factory, User 1-8, Add-On 1-32— Imports add-on
sample libraries from a properly formatted USB flash drive/thumb drive
(see “Formatting a USB Flash Drive” on page 120) connected to the
sample import
port on the rear of the Prophet X.