10
SECTION 3:
SECTION 3:
SECTION 3:
SECTION 3:
SECTION 3: SETUP AND
SETUP AND
SETUP AND
SETUP AND
SETUP AND TESTING SYSTEM
TESTING SYSTEM
TESTING SYSTEM
TESTING SYSTEM
TESTING SYSTEM
3.1
3.1
3.1
3.1
3.1
POWERING UP THE CONTROL
POWERING UP THE CONTROL
POWERING UP THE CONTROL
POWERING UP THE CONTROL
POWERING UP THE CONTROL
Before applying power to the system, recheck all wiring connec-
tions, verifying polarity.
Plug the AC transformer into an unswitched 120vac receptacle.
Connect the battery leads to the battery. Red lead to the positive (+)
terminal, black lead to the negative (-) terminal of the battery. If the
battery is not fully charged, allow 36 hours for the battery to fully
charge. The keypad will now display system status.
NO
NO
NO
NO
NOTE:
TE:
TE:
TE:
TE: Re
Re
Re
Re
Rever
ver
ver
ver
versing batter
sing batter
sing batter
sing batter
sing battery wires will cause the factor
y wires will cause the factor
y wires will cause the factor
y wires will cause the factor
y wires will cause the factory replace-
y replace-
y replace-
y replace-
y replace-
ab
ab
ab
ab
able fuse FL1 to b
le fuse FL1 to b
le fuse FL1 to b
le fuse FL1 to b
le fuse FL1 to blo
lo
lo
lo
low
w
w
w
w.....
Program the
EEPROM
for the desired system configuration and
features. Refer to the SC programming instructions, Section 8 of
this manual. After programming is complete, restore the system
back to the normal mode.
3.2
3.2
3.2
3.2
3.2
TESTING THE LOCAL SYSTEM
TESTING THE LOCAL SYSTEM
TESTING THE LOCAL SYSTEM
TESTING THE LOCAL SYSTEM
TESTING THE LOCAL SYSTEM
The system can be armed and disarmed from the keypad using the
factory default code [1111] or any user code previously assigned.
The system may also be armed and disarmed using a keyswitch,
if so programmed. Leave the system disarmed.
NO
NO
NO
NO
NOTE:
TE:
TE:
TE:
TE: Bef
Bef
Bef
Bef
Before testing comm
ore testing comm
ore testing comm
ore testing comm
ore testing communication to the central
unication to the central
unication to the central
unication to the central
unication to the central
repor
repor
repor
repor
reporting station,
ting station,
ting station,
ting station,
ting station, connect the telephone connection
connect the telephone connection
connect the telephone connection
connect the telephone connection
connect the telephone connection
cab
cab
cab
cab
cable into the RJ31-X jac
le into the RJ31-X jac
le into the RJ31-X jac
le into the RJ31-X jac
le into the RJ31-X jack.
k.
k.
k.
k.
Testing the system using the keypad:
Arm the system in the test mode.
Press
[PPPP] +
[PPPP] +
[PPPP] +
[PPPP] +
[PPPP] +
▲
*
■
4
+
+
▲
#
The audible warning device will pulsate continuously during TEST,
except when testing an Entrance Delay zone. During Entrance Delay
time, the audible warning device will change to a steady sound (for
4 seconds in the TEST MODE), and then return to a pulsating sound.
All loops may now be tested independently. Violate each loop
separately. The Arm led will flash and the zone in alarm will be
indicated. No need to reset panel after each zone test. Bell or Siren
will shut off in 4 seconds and another zone can be tested.
NO
NO
NO
NO
NOTE:
TE:
TE:
TE:
TE: Zones violated while in the
Zones violated while in the
Zones violated while in the
Zones violated while in the
Zones violated while in the TEST MODE will not repor
TEST MODE will not repor
TEST MODE will not repor
TEST MODE will not repor
TEST MODE will not reporttttt
to the Central Repor
to the Central Repor
to the Central Repor
to the Central Repor
to the Central Reporting Station.
ting Station.
ting Station.
ting Station.
ting Station. After all zones are tested,
After all zones are tested,
After all zones are tested,
After all zones are tested,
After all zones are tested,
Disarm the panel.
Disarm the panel.
Disarm the panel.
Disarm the panel.
Disarm the panel. All audib
All audib
All audib
All audib
All audible warning de
le warning de
le warning de
le warning de
le warning devices will shut off and
vices will shut off and
vices will shut off and
vices will shut off and
vices will shut off and
the Arm LED will turn off
the Arm LED will turn off
the Arm LED will turn off
the Arm LED will turn off
the Arm LED will turn off.....
THE
THE
THE
THE
THE TEST MODE IS NO
TEST MODE IS NO
TEST MODE IS NO
TEST MODE IS NO
TEST MODE IS NOT A
T A
T A
T A
T AV
V
V
V
VAILABLE IN
AILABLE IN
AILABLE IN
AILABLE IN
AILABLE IN THE MUL
THE MUL
THE MUL
THE MUL
THE MULTI-PREMISE
TI-PREMISE
TI-PREMISE
TI-PREMISE
TI-PREMISE
P
P
P
P
PAR
AR
AR
AR
ARTITION MODE
TITION MODE
TITION MODE
TITION MODE
TITION MODE BUT
BUT
BUT
BUT
BUT THE COMMAND CAN BE USED
THE COMMAND CAN BE USED
THE COMMAND CAN BE USED
THE COMMAND CAN BE USED
THE COMMAND CAN BE USED T
T
T
T
TO
O
O
O
O
CLEAR A "F
CLEAR A "F
CLEAR A "F
CLEAR A "F
CLEAR A "FAIL
AIL
AIL
AIL
AIL T
T
T
T
TO COMMUNICA
O COMMUNICA
O COMMUNICA
O COMMUNICA
O COMMUNICATE" INDICA
TE" INDICA
TE" INDICA
TE" INDICA
TE" INDICATION.
TION.
TION.
TION.
TION.
3.3
3.3
3.3
3.3
3.3
TESTING COMMUNICATION TO THE CENTRAL
TESTING COMMUNICATION TO THE CENTRAL
TESTING COMMUNICATION TO THE CENTRAL
TESTING COMMUNICATION TO THE CENTRAL
TESTING COMMUNICATION TO THE CENTRAL
REPORTING STATION
REPORTING STATION
REPORTING STATION
REPORTING STATION
REPORTING STATION
Arm the panel. Violate a zone. The Siren/Bell should turn on, the arm
led will flash and the zone in alarm will be indicated, the premise
telephone should be inoperative (DEAD). After the Central Report-
ing Station receives a good transmission of this violation, it will send
a "Kiss-off" signal back to the panel and disconnect from the
telephone line, returning premise phone back to normal.
