Sentera FCVC8-R Mounting And Operating Instructions Download Page 4

Page: 4 / 12

www.sentera.eu

MIW-FCVC8-R-EN-000 - 28 / 08 / 2019

4 - 12

back to the table of contents

PRODUCT DESCRIPTION

The FCVC8-R series are intelligent sensors featuring adjustable temperature,
relative humidity and TVOC / CO

eq ranges. Based on this TVOC measurement,

an equivalent CO

level (CO

eq) is calculated. The TVOC concentration is an

accurate indicator for indoor air quality. Based on the temperature and relative
humidity measurements, the dew point is calculated. The used algorithm
controls a single analogue / modulating output based on the measured T,
rH and TVOC values, which can be used to directly control an EC fan or an
actuator powered damper. All parameters are accessible via Modbus RTU.

ARTICLE CODES

Article

code

Supply Maximum power

consumption

Nominal power

consumption

Imax

FCVC8-R

85—264 VAC / 50—60 Hz

0,76 W

0,63 W 30 mA

INTENDED AREA OF USE

■

Ventilation based on temperature, relative humidity and TVOC levels for indoor
applications

■

Demand controlled ventilation

■

For indoor use only

TECHNICAL DATA

■

Demand controlled ventilation, based on T, rH and TVOC

■

Analogue / modulating output type:

►

0—10 VDC mode: min. load 50 kΩ (R

≥ 50 kΩ)

►

0—20 mA: max. load 500 Ω (R

≤ 500 Ω)

►

PWM (open-collector type): PWM Frequency: 1 kHz, min. load 50 kΩ (R

≥ 50 kΩ);

PWM voltage level 3,3 or 12 VDC

■

Selectable temperature range: 0—50 °C

■

Selectable relative humidity range: 0—100 %

■

Selectable TVOC range: 0—60.000 ppb

■

Replaceable TVOC / CO

eq sensor element

■

3 LEDs with adjustable light intensity for status indication

■

Accuracy: ±0,4 °C (range 0—50 °C); ±3 % rH (range 0—95 % rH); ±30 ppm TVOC
(range 0—60.000 ppb)

■

Inset or surface mounting

■

Enclosure:

►

internal: plastic RABS, black

►

external: ABS, white

►

cover: ASA, white

■

Protection standard: IP30 (according to EN 60529)

■

Typical field of use:

►

temperature: 0—50 °C

►

rel. humidity: 0—95 % rH, (non-condensing)

■

Storage temperature: -10—60 °C

STANDARDS

►

Low Voltage Directive 2014/35/EC;

►

EN 60529:1991 Degrees of protection provided by enclosures (IP Code)
Amendment AC:1993 to EN 60529

►

EN 60730-1:2011 Automatic electrical controls for household and similar use -

FCVC8-R

INTELLIGENT MULTIFUNCTIONAL
FLUSH MOUNTED SENSOR

Summary of Contents for FCVC8-R













Search results

Summary of Contents for FCVC8-R

Reviews:

Related manuals for FCVC8-R

Brands by name

Popular brands

Sentera FCVC8-R, Mounting And Operating Instructions

Search results

Summary of Contents for FCVC8-R

Reviews:

Related manuals for FCVC8-R

Brands by name

Popular brands