background image

www.sentera.eu

MIW-MT-EN-000 - 18 / 10 / 2021

4 - 8

back to the table of contents

MT

ELECTRONIC FAN SPEED 
CONTROLLER

PRODUCT DESCRIPTION

The MT controllers provide manual control of the rotational speed of voltage 
controllable motors (230 VAC / 50 Hz) by varying the supplied voltage through 
phase angle control. They are suitable for both inset and surface mounting. Several 
motors can be connected as long as the current limit is not exceeded. All models 
have an extra (unregulated) 230 VAC output. 

ARTICLE CODES

Output regulation from minimum to maximum

Code

Current range, [A] 

Fuse, [A] (5*20  mm)

MTY-0-05-AT

 0,05—0,5

F-0,63 A-H 

MTY-0-15-AT

0,1—1,5

F-2,00 A-H 

MTY-0-25-AT

0,2—2,5

F-3,15 A-H

MTY-0-40-AT

0,4—4,0

F-5,00 A-H

Output regulation from maximum to minimum

Code

Current range, [A] 

Fuse, [A] (5*20  mm)

MTX-0-05-AT

 0,05—0,5

F-0,63 A-H 

MTX-0-15-AT

0,1—1,5

F-2,00 A-H 

MTX-0-25-AT

0,2—2,5

F-3,15 A-H

MTX-0-40-AT

0,4—4,0

F-5,00 A-H

INTENDED AREA OF USE

 

Manual control of the motor / fan speed in HVAC applications

 

For indoor use only

TECHNICAL DATA

 

Infinitely variable fan speed control

 

Power supply: 230 VAC ±10 % / 50 Hz

 

Unregulated input / output: 230 VAC / max. 2 A

 

OFF position can be disabled to obtain continuous operation of the fan

 

Regulated output: 80—230 VAC

 

Minimum speed adjustment by trimmer

 

Speed control:

 

MTX – from maximum to minimum

 

MTY – from minimum to maximum

 

Enclosure: 

 

External: ASA, white-ivory (RAL9010), IP54 (according to EN 60529)

 

Internal: polyamide, white-ivory (RAL9010), IP44 (according to EN 60529)

 

Operating ambient conditions:

 

temperature: 0—35 °C

 

rel. humidity: < 100 % rH (non-condensing)

 

Storage temperature: -10—40 °C

STANDARDS

 

Low Voltage Directive 2006/95/EC 

 

 EN 60335-1:2012 Household and similar electrical appliances - Safety - Part 1: 
General requirements. Amendment A11:2014 and AC:2014 to EN 603351;2012 

 

 EN 61558-1:2005 Safety of power transformers, power supplies, reactors and 
similar products - Part 1: General requirements and tests. Amendment A:2006 
and A1:2009 to EN 61558-1:2005

Summary of Contents for MT









Reviews: