SenTech STC-CL500E User Manual Download Page 31

Page: 31 / 32

No.11S031-03

STC-CL500E/CLC500E
Users guide Rev. 1.3

4.4.3 Sequence for the command saves to the EEPROM

Please use below sequence for the command saves to the EEPROM

1) Set “1” to the 80H.0 for the accept “write control to the EEPROM”.

2) Send the command and the save data with the EEPROM access command, which is set “1” for the page

selection.

3) The camera send back the one of the below receiving code after write EEPROM.

01H: OK
10H: EEPROM write error

4) 80H.0 is changed to “0” automatically after write EEPROM.

Note.1) DO NOT saves to the EEPROM when 80H.0 is “0”.

Note.2) When save the multiple sequence command to the EEPROM, all data save to the EEPROM by one

operation from 1) to 4).
Example of the multiple sequence command: “10H, 11H, 12H and 13H” or “22H, 23H and 24H”.

Note.3) When save the multiple command data, which is not sequence command, to the EEPROM, it is

necessary to operate the number of times from 1) to 4).
Example of the multiple command: “10H, 13H, 19H and 1BH” or “20H, 23H and 25H”.

Summary of Contents for STC-CL500E

































Search results

Summary of Contents for STC-CL500E

Reviews:

Related manuals for STC-CL500E

Brands by name

Popular brands

SenTech STC-CL500E, User Manual

Search results

Summary of Contents for STC-CL500E

Reviews:

Related manuals for STC-CL500E

Brands by name

Popular brands