SenTech STC-CL500E User Manual Download Page 30

Page: 30 / 32

No.11S031-03

STC-CL500E/CLC500E
Users guide Rev. 1.3

Command No.
79H:
EFFCT[7..0]

00H: No effect (Original video), 01H: 11bit gradation,
02H: 10bit gradation,

03H: 9bit gradation,

04H: 8bit gradation,

05H: 7bit gradation,

06H: 6bit gradation,

07H: 5bit gradation,

08H: 4bit gradation,

09H: 3bit gradation,

0AH: 2bit gradation,

0BH: 1bit gradation,

0C to FEH: No function,
FFH: MSB-LSB reverse

80H:
E2P[7..0]

D7 to D1: No function

Sets always as "0000000"

D0:

Write control to the EEPROM

0: Prohibited,

1: Accept

F0H:
OUTSEL[7..0]

D7 to D4: No function

Sets always as "0000"

D3 to D0:

Note: Change the C0H address data of the register and save to EEPROM
when save the signals of the power/IO connector to the EEPROM.

[The signals of the power/IO connector] Initial data: OUTSEL[7..0] = The value of C0H

D[7..0]

Initial data: 0000, data range: 0000 to 0111

Please refer "1.2 The signals of the power/IO connector

The signals of the power/IO connector selection

Command descriptions

[EEPROM control] Initial data: E2P[7..0] = 0

D[7..0]

[Image effect selection] Initial data: EFFCT[7..0] = 0
Sets the imgae effect.

D[7..0]

Note: This bit is cleared to "0" automatically by the internal process after the execution
of the command.

Summary of Contents for STC-CL500E

































Search results

Summary of Contents for STC-CL500E

Reviews:

Related manuals for STC-CL500E

Brands by name

Popular brands

SenTech STC-CL500E, User Manual

Search results

Summary of Contents for STC-CL500E

Reviews:

Related manuals for STC-CL500E

Brands by name

Popular brands