manualshive.com logo in svg

SensorTherm METIS H3 series, User Manual, Page: 9 / 66

Share
Download
SensorTherm METIS H3 series User Manual Download Page 9

METIS M308 / M309 / M313 / M316 / M318 / M323 / H309 / H316 / H318 (12-pin) 

Electrical Connection

 

 

 

9 

M3 / H3

 

0 V

 

White 

Brown

 

+24 V

 

Operating 
status LED 

4.1.1  Factory Settings 

Parameters 

Factory settings 

 

Temperature sub range ........................................ corresponds to basic range 
Response time t

90

 ................................................. Min (corresponds to: M3: <1 ms; H3: <40 µs) 

Emissivity ε ........................................................... 1.000 (corresponds to 100%) 
Transmittance ....................................................... 100% 
Spot size fill factor ................................................. 100% 
Serial interface RS232 / 485 ................................. RS485 
Data transmission speed (baud rate) .................... 115.2 kBd 
Buffer mode .......................................................... 

Off (at “on”: buffer interval: 100 ms, single reading)

 

Upscale Burnout function ...................................... Off 
Device address ..................................................... 00 
Command delay .................................................... 00 (for RS232 and RS485) 
Maximum value storage ........................................ Off 
Laser targeting switch-off time .............................. 180 s 
Analog output 1 ..................................................... 4

–20 mA, output temperature: measured temperature 

Analog output 2 ..................................................... 4

–20 mA, output temperature: no temperature output 

Digital input / output 1 ........................................... set to input: external switching on / off targeting light  
Digital input / output 2 ........................................... set to input: maximum value storage external clearing  
Digital input / output 3 / Analog in ......................... set to input: no function 

Input debounce time ....................................... 100 ms 
Output activation time .................................... 0 ms 
Output hold time ............................................. 10 ms 
Limit switch: .................................................... Center of temp. range °C / °F; hysteresis: 10°C / 20°F 
Device over temperature: ............................... 50°C / 120°F; hysteresis: 2°C / 5°F 

 

 

With integrated PID controller: 

Analog output 2 ................ 0-20 mA, output set to  

control output 

Digital input / output 2 ....... Digital input: controller start 
Setpoint ............................ Center of temp. range  
Proportional band Xp ........ 1% 
Derivative time Td ............ 0 ms 
Integral time Ti .................. 10 ms 
Sampling time ................... 10 ms 

Ramp time ............ 0 ms 
P-zsc ..................... 100% 
P-max ................... 100% 
P-min .................... 0% 
P-Dyn .................... 100% 
AutoTune .............. at each start (power: 50%) 
Ramp time ............ 0 ms 
Hold time .............. 0 ms 

 

 

INFO to baud rate:

 The factory setting of the baud rate is set to 115 kBd to ensure also at 

longer interface cables a working data transfer. For data transmissions with the highest speed, 
baud rate and buffer mode must be adjusted (see 

7.2.3.4

) 

 

With integrated Profibus-DP / Profinet: 

Field bus mode: ................................ Fixed standard format M3 series 
Address ............................................. 126 (delivery address) 

 
 

4.1.2  Power Supply 

With connection to the supply voltage (standard 24 V DC, possible range 18

–

30 V) the unit is ready for operation with the factory settings. 
By connecting the power supply, the current firmware version is displayed for a 
few seconds. 
Interrupt the power supply to turn off the pyrometer, e.g. by disconnecting 
the connector. 

 

The 

operating status

 is displayed on the 

LED 4

: 

 

Orange

 in the self-test phase (M3 ca. 2 s; H3 during the initialization 

and thermostatic phase for ≤ 3 min.) 

 

Green

 when the pyrometer is ready 

 

Red

 when an error occurred (see 

10.4

 

Trouble-shooting

). 

Summary of Contents for METIS H3 series



































































Reviews:

No comments