manualshive.com logo in svg

Sensaphone Sentinel Pro, Installation And Setup Manual, Page: 18 / 44

Share
Download
Sensaphone Sentinel Pro Installation And Setup Manual Download Page 18

18

Sentinel Pro Installation and Setup Guide

your device status is OK. If it is red, your device has alarms. You can click on the icon to show the zone 

values for the selected device. 

The device table will display all devices on your account. Click on the 

Details

 button to display and con-

figure the zones for that device. You can also use the search box above the table to search through the 

table, or click on the table column headers to sort the data. 

Device Name 

– The name of the device

Status

 – The current status of the device (Okay, Alarms, Offline, or Standby) If the device has any 

unacknowledged alarms, a symbol will be displayed in this column

Power

 – Displays if the device is On or Off (--- will display if the device is offline)

Battery

 – The current percentage of the device battery (--- will display if the device is offline)

Last Response

 – The time that the device last connected to the server

standby Mode

Standby mode puts the Sentinel Pro in a temporary state such that no alarms will be detected, allowing 

onsite personnel to perform maintenance or other tasks that may have triggered an alarm otherwise. 

Standby mode can be entered using the Action drop down on the Dashboard page or via the pushbut-

ton on the front of the unit. Standby mode will persist for the duration of time entered on the Device 

Configure screen and will automatically exit once the time expires. When using the pushbutton you 

must depress the button for 5 seconds. The Standby LED will light up to indicate that the device is in 

Standby mode. You can also exit Standby mode using the same methods.

Standby

 – Allows you to put the selected devices into Standby mode

Enter

 – Put the Sentinel Pro in Standby mode for the length of time that is set on the Device 

Configure page

Enter (Untimed) 

– Put the Sentinel Pro in Standby mode until you disable it

Exit

 – Take the device out of Standby mode

Summary of Contents for Sentinel Pro













































Reviews:

No comments