manualshive.com logo in svg

Sensaphone Sentinel Pro, Installation And Setup Manual, Page: 12 / 44

Share
Download
Sensaphone Sentinel Pro Installation And Setup Manual Download Page 12

12

Sentinel Pro Installation and Setup Guide

Wall Mount InstallatIon

The Sentinel Pro can be wall mounted using dry wall anchors and (4) #8 screws. Follow the steps 

below:

1) Install four drywall anchors (if necessary). Attach the Sentinel Pro using four #8 tapping screws. See 

Figure 2 for dimensions. 

2) Attach sensors to the zone terminals.
3) Plug the power adaptor into a 115VAC 50/60Hz outlet.
4) Connect a CAT5 cable to the Ethernet port and connect to a 10/100 network hub, switch or router.

5.75”

3.00

Figure 2: Sentinel Pro mounting dimensions

sentInel Cellular VersIon

The Cellular version of the Sentinel Pro includes a 4G modem and battery backup system to keep the 

entire unit functioning for up to 8 hours. A special Battery Backup Controller is included to maintain 

proper charging of the 12V backup battery and automatically switchover when power fails. The unit is 

packaged in a NEMA-4X Polycarbonate enclosure with a universal 12V power supply. Cellular subscrip-

tion plans are available from Sensaphone.
Mounting Dimensions (Cellular):

10.54”

268mm

13.3”

334mm

Summary of Contents for Sentinel Pro













































Reviews:

No comments