background image

Using the headset system

30

To start the conference call using the master headset:

Establish a wireless link between headset and base station (the LINK 
LED 

 flashes blue).

To add a guest headset to the conference call:

Place the guest headset to be added to the conference call into the base 
station of the master headset.
The HEADSET LED 

 flashes blue/red and the headset pairs to the base 

station. If pairing was successful, the HEADSET LED 

 lights up blue.

Take the guest headset out of the base station.
You hear a beep in the master headset.

Press the LINK button 

 

 on the master headset within 15 seconds.

The guest headset is enabled for the conference call.

If necessary, repeat this procedure for the two other guest headsets.

Call the other party.

To exit the conference call with a guest headset:

Press the LINK button 

 

 on the guest headset.

To end the conference call:

Use the master headset to end the conference call.
The wireless links to all other headsets participating in the conference 
call are disconnected.

Pairing the headset to third party DECT GAP telephones

Place the DW Office headset at a maximum distance of 1 m from the 
non-DW Office base station.

Simultaneously press and hold the headset’s LINK button 

 

 an

AUDIO button 

 for 5 seconds.

The headset switches to setting mode/GAP pairing mode and the 
HEADSET LED 

 flashes blue/red. 

Set the non-DW Office base station to GAP pairing mode (see the 
instruction manual of the non-DW Office base station).
The headset pairs to the non-DW Office base station. If pairing was 
successful, the HEADSET LED 

 goes off.

3

4

You can only end the conference call using the master headset. 
Other functions such as volume adjustment and muting the 
headset’s microphone can still be performed on each headset.

The DW Office base station can only  be  used  with  DW  Office 
headsets.

The standard code for DW Office is “

0000

”.

Summary of Contents for 504302













































Reviews: