background image

ENGLISH 2/8

GENERAL FEATURES

TECHNICAL SPECIFICATIONS

Communication

MI002875-E

Power supply and serial connection wiring facilitated by means of a bus that can be 

used in the DIN guide.

Functioning modality is configurable by DIP-switch.

RS485 serial communication with protocol MODBUS-RTU

High immunity to the RF disturbs

Transparent to the ModBUS protocol

Isolation between communication and power supply: 1500 Vac.

It is possible to implement MESH networks

BRIDGE or REMOTE I/O functioning

The  Z-LINK1  modules  represent  a  communication  systems  for  data  acquisition  and 
transmission  in  the  process  control  and  industrial  /  civil  automation.  Based  on  an  UHF 
modem  radio,  Z-LINK1  is  able  to  comunicate  with  Z-PC  line  modules  through  ModBUS 
protocol. Z-LINK1 represents a new platform communication in radio frequency.
   

Interface :

ModBUS RTU protocol

 :

Delay between polls :
Timeout (master Modbus) :                         

Frequency band

 :

Modulation

 :

Class of radio module

 :

Performance in free field 
conditions

 :

Radiated power

:

Communication

 :

- RS232
- RS485
- Half-duplex functioning module (the communication 
between devices occurs in alternate way)
Yes
> 200 ms (to set in the master Modbus)
> maximum between all timeout values configured in 
the Easy setup software
g3, attached 1 ERC 70-03 (869.4 MHz - 869.650 MHz)
GFSK
2

-3

400 m (with PER<10  @ 57.6 kbaud, with antenna 
accessory ANT-MAG placed over 2 m from the soil)
20 mW
32 nodes

Electrical features

Power supply :
Consumption :

LED status

10..40 Vdc or 19..28 Vac (50..60 Hz)
1 W @ 12 Vdc (without radio communication)
1 W @ 24 Vdc (without radio communication)
1 W @ 24 Vdc (with radio communication)

- Power supply
- Data transmission via bus
- Data transmission via radio
- Test after installation

Summary of Contents for Z-LINK1









Reviews: