background image

ENGLISH 3/8

Communication ports 

RS485 terminal: 10, 11, 12 

Baud rate 115200 baud max 

Ethernet 

Fast Ethernet 10/100 Mbps 
Communication port: front with RJ45 connector 
Connection maximum distance 100m 

Side USB 

Plug-in: Micro USB 

Digital input (pulsed Q flow measurement) 

Input type: PNP / Absorbed current: 3mA 
Voltage and internal power supply: 12V / 20mA / Maximum frequency: 250 Hz. 

Analogue inputs 1 and 2 Voltage/Current 

(A1 Q flow measurement, A2 Pressure P measurement / Temperature T) 

Number of channels: 2 / Input type: configurable mA or V / Resolution: 16 bit 
Voltage input: 0 – 30 V / precision 0.1% of Full Scale 
Current input: 0 – 20 mA / precision 0.1% of Full Scale / Input protection: 30 V / 25 mA / Max voltage 
drop: 1.2 V 

Universal analogue input 3 

(Temperature measurement T) 

Type: V / mA 2 wires passive / mA 4 wires active / RTD 2 wires / RTD 3 wires / RTD 4 wires 
Resolution: 15 bit / Sampling: 20ms (50Hz rejection)  
INPUT TYPE: 
voltage 0 – 10 V / Input impedance: 120kΩ 
current: 0 – 20 mA / Input protection: 30 V / 25 mA / Max voltage drop: 1.2 V 
resistance thermometer (RTD): PT100 / 500 / 1000 / NI100 connection with 2 / 3 / 4 wires with burnout 
detection. 

Analogue output 

Type: configurable V – mA / Resolution: 14 bit / Width-limited signal. 
Voltage output: 0 – 10 V (minimum load resistance = 1kΩ), 
Current output (active / passive):0 – 20 mA (maximum load resistance 600Ω), 
Precision: 0.1% / Thermal stability: 0.01%/°K / Linearity error: 0.01% / EMI < 1%. 

Digital outputs 

Number of channels: 2 / Type: SPDT free contact relay / Voltage: 30 V

 / 30 V

 / Current: 2 A. 

Power supply 

Voltage 

10 – 40 V

; 19 – 28 V

  50 – 60 Hz 

Absorption 

Max.: 

5

 W @ 24V

 

Internal batteries 

2xAAA NiMH 

Environmental conditions 

Temperature 

-10 – +40°C (limit with UPS recharge battery)
-10 – +50°C (limit without UPS recharge battery)

Humidity 

30 – 90% to 40°C non condensing 

Altitude 

up to 2000 m above sea level 

Storage temperature 

-20 – +45°C (< 6 months)

Protection rating 

IP20 

Connections 

3-way removable screw terminals, pitch 5 mm
RJ45 and micro USB 
Micro SD card slot 

Overall dimensions / Case 

Dimensions/Weight 

L: 100 mm; H: 112 mm; W: 52.5 mm  / 315 gr. 

Case 

PA6, black 

MI003722-

E

 

Summary of Contents for Z-FLOWCOMPUTER









Reviews: