Sencor SWD 130 User Manual Download Page 8

EN-6

Troubleshooting

Error

Cause

Remedy

Notes

Transmitter 
indicator is 
not lit

Batteries are 
not inserted 
correctly

Check the positive 
and negative poles 
on the high-capacity 
batteries: batteries 
are inserted into the 
battery compartment 
with the negative 
pole facing the 
front part of the 
transmitter.

Battery type 
CR 2032 may also 
be used. It can 
be purchased in 
supermarkets, 
watch repair 
stores, toy stores 
or in online stores.

The receiver is 
not working

Indicator is not lit The power supply 

is not connected 
correctly or the 
batteries are not 
inserted correctly.

If you are unable 
to resolve this 
problem, please 
contact the 
manufacturer.

The indicator is lit 
but the bell does 
not chime

The learning code is 
incorrect; please reset 
it according to the 
instructions.

Transmission 
distance is 
shortened

Transmission 
distance is 
affected by 
the wireless 
electronic 
product coming 
close to metal 
objects.

A test field 
demonstrated 
that the effective 
transmission distance 
is reduced when 
the transmitter 
is installed near 
metal doors or in 
locations with large 
electromagnetic 
interference. 
Likewise, too many 
walls results in 
interference to the 
signal.

This product 
should be installed 
away from 
metal objects: 
when suitable 
installation 
location are not 
available, extend 
the distance 
between the 
transmitter and 
metal objects.

No signal is being 
received

Batteries are flat

Replace the batteries 
in the transmitter

Sound is 
distorted

Batteries are flat

Replace the batteries

Summary of Contents for SWD 130










Reviews: