- 9 -
07/2019
Copyright © 2019, Fast ČR, a.s.
■
Slide the dust container out of the water tank.
■
Attach the mop fabric to the underside of the water tank using the velcro zip
E4
on the water tank.
■
Open the cap
E5
and fill the tank with water. Properly insert the cap back in. Wipe
any excess water off the water tank. Take special care to ensure that the contacts
E6
are dry.
Note
:
For wiping, we recommend using clean water. If you use a cleaning
agent, it may foam up and thereby worsen the dripping of the water
on to the fabric, or potentially cause smudges on the floor after it dries.
■
Insert the dust container back into the water tank and insert this assembly back into
the vacuum cleaner.
■
Start the vacuum cleaner.
SCHEDULED CLEANING
Note:
The scheduled cleaning time setting is based on the system time of the
vacuum cleaner. Therefore, before setting the scheduled cleaning time,
it is necessary to correctly set the system time as described in chapter
SETTING THE SYSTEM TIME OF THE ROBOTIC VACUUM CLEANER.
■
This function enables scheduling the vacuum cleaner to automatically start cleaning
at a certain time once per day. If you use the application, it is possible to schedule
a cleaning time for every day at a different time. Please follow the instructions in
the application.
■
This function behaves as a delayed start, so you are actually setting a delayed
cleaning time. Example: If the current time on the vacuum cleaner is 5:00 p.m.
then by setting the scheduled cleaning time to 2:30 the vacuum cleaner will
automatically start cleaning only at 7:30 p.m. If you leave the main switch of the
vacuum cleaner turned on, then the same cleaning process will be repeated at 7:30
p.m. every day thereafter.
Attention:
Never use the delayed cleaning function for wet wiping when
the water tank is filled with water. This could result in excessive
wetting of the floor in the vicinity of the charging station.
Setting scheduled cleaning:
■
In the stand-by mode or in the charging in the charging station mode, hold down
button
C3
(PLAN) until the time setting value starts flashing on the display
C2
.
■
Using buttons
C5
(
) or
C8
(
) set the time values. Toggle between the values
using buttons
C6
( ) or
C7
( ).
■
Confirm the set time by pressing button
C9
(ON/OFF). 1× beep will be made and
the set time will be saved to memory as the automatic cleaning time. The vacuum
cleaner will clean at this time every day.
Note:
If you turn off the robotic vacuum cleaner using the main switch, the
scheduled cleaning time will be deleted. If you wish to use automatic
cleaning, then it is necessary to leave the vacuum cleaner in the
charging station.
Cancelling scheduled cleaning
■
Hold down button
C3
(PLAN). The set automatic cleaning time will start flashing
on the display
C2
.
■
Hold down button
C9
(ON/OFF) until 00:00 appears on the display. Pressing button
C9
again will cancel the set time and the vacuum cleaner will beep 2×.
■
Hold down button
C3
(PLAN) to return to the display of the system time.
CONTROLLING THE ROBOTIC VACUUM CLEANER USING THE
MOBILE APPLICATION
■
The vacuum cleaner can also be controlled using a smartphone or tablet. The
application enables you to select the cleaning mode, stop the cleaning process or
send the vacuum cleaner to the charging station; it provides an overview of how
much time was spent cleaning and about the condition of the vacuum cleaner.
■
The application is freely available in the
Apple App Store
or
Google Play Store
. This
link for this application is found in the picture part of this user's manual.
Note:
The robotic vacuum cleaner supports Wi-Fi in the 2.4 GHz frequency
band. If unsure about which standards are used by your Wi-Fi network
and your router, please contact your internet service provider or the
manufacturer of the router.
■
After downloading and installing it, the application will guide you through the
process for connecting the vacuum cleaner to your Wi-Fi network. The pairing of the
vacuum cleaner with your Wi-Fi is indicated by symbol
D2
being lit.
CHARGING THE ROBOTIC VACUUM CLEANER
AUTOMATIC CHARGING
■
As soon as the vacuum cleaner detects low voltage of the battery during operation,
it will automatically start to seek out the charging station. In order for it to find it and
dock, it needs to find the infrared signal transmitted by the charging station. For this
reason, we recommend leaving the charging station constantly connected to the
power source and located in accordance with the instructions provided in chapter
LOCATION OF THE CHARGING STATION.
■
After docking in the charging station, the charging cycle will commence. A complete
charge takes approximately 4 to 7 hours. The actual charging time depends on the
power level of the battery. A fully charged battery will provide up to 120 minutes
of operation.
■
During the charging process, the indicator light on button
D1
will alternately flash
red and blue.
■
When the battery is fully charged, the indicator light of button
D1
will remain
permanently lit blue and the process will end automatically.
■
In the event that the charging contacts are disconnected during the charging cycle,
the vacuum cleaner will move away from the charging station and then re-dock
itself to resume the charging process, unless it is prevented from doing so by an
obstacle. In the event of a power outage, the charging cycle will be interrupted and
will continue after the power supply is renewed. In the event that the maximum
charging current is exceeded, the charging station will automatically interrupt the
charging cycle.
MANUAL CHARGING
■
If the vacuum cleaner is located away from the charging station and detects a low
battery voltage then button
D1
will be lit red. Press button
C4
(HOME) on the
remote control. The vacuum cleaner will automatically seek out the charging station
and start automatic charging as described in the previous chapter.
■
If the battery is so flat that the vacuum cleaner is unable to seek out the charging
station then it is necessary to dock the vacuum cleaner into the charging station
by hand. Grasp the vacuum cleaner and manually place it into the charging station
so that the charging contacts on the underside of the vacuum cleaner and the
charging contacts on the charging station are connected. When the contacts are
connected, charging will start.
■
The vacuum cleaner can also be charged without using the charging station. Insert
the power adapter connector into socket
A4
on the side of the vacuum cleaner and
insert the power adapter plug into a mains socket.
CARING FOR THE BATTERY
■
We recommend that you do not interrupt the charging cycle and maintain the
battery in a charged state.
■
Do not leave the vacuum cleaner standing fully charged or completely flat for an
unnecessarily long period of time.
■
A battery that is allowed to remain flat for a long time may self-discharge below
a permissible level and thereby cause irreparable damage to itself.
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
SOLUTION
The vacuum
cleaner cannot
be turned on.
The battery is not inserted
correctly in the robotic
vacuum cleaner.
Insert the battery according
to the instructions in this
user's manual.
The battery is flat.
Charge the battery.
The vacuum
cleaner is on,
but it is not
vacuuming dust
and dirt.
The dust container is full.
Empty the dust container.
The dust filter is not properly
installed in the dust container.
Properly install the dust filter
into the dust container.
The vacuum
cleaner travels
only backwards
when it is turned
on.
The vacuum cleaner was
placed on a floor that is
too dark.
Move the vacuum cleaner to
a lighter-coloured floor and
start it again.
An anti-fall sensor is dirty.
Clean the anti-fall sensors.
The rotary
brushes are
deformed and
do not sweep up
dust and dirt.
The brushes are worn out.
Dip them in warm water to
renew their original shape.
Contact the vendor or service
centre and order new brushes.
VOICE MESSAGES
MESSAGE
SOLUTION
Turn on the vacuum cleaner
Dock the robot into the charging station.
If the vacuum cleaner was lifted, put it down
on the floor
Anti-fall sensors are dirty. Clean them.
Sensor sent a false error. Turn the vacuum cleaner
off and on.
Check that the bumper bar returns correctly
after being pushed in. If not, contact the service
department.
Overload of one of the rubber wheels, probably
due to dirty material or jamming on an obstacle.
Check that the wheels are clean and remove any
dirty material or obstacles.
