- 8 -
07/2019
Copyright © 2019, Fast ČR, a.s.
INSERTING AND REPLACING BATTERIES IN THE REMOTE CONTROL
■
Push down the latch of cover
C13
on the rear side of the remote control
C1
to
release it and remove the cover.
■
Insert two type AAA (1.5 V) batteries into the remote control. When inserting the
batteries, ensure the correct polarity as shown inside the battery compartment
C14
.
Put the cover
C13
back on and click it into place.
■
In the event that the batteries are flat, replace them with new ones. Do not combine
various types of batteries or new and old batteries.
■
The signal range of the remote control is approximately 6 m.
SETTING THE SYSTEM TIME OF THE ROBOTIC VACUUM CLEANER
■
The system time of the vacuum cleaner is the actual time according to your time
zone. It must be correctly set if you wish to use the scheduled cleaning function.
■
In the stand-by mode or in the charging in the charging station mode, hold down
button
C11
(CLK) until the time setting value (hours and minutes) starts flashing
on the display
C2
.
■
Using buttons
C5
(
) or
C8
(
) set the time values. Toggle between the hour and
minute numbers using buttons
E6
( ) or
C7
( ).
■
Confirm the set time by pressing button
C11
(CLK). 1× beep will be made and the set
time will be saved to memory as the system time.
■
If you do not perform any changes within 10 seconds, the system time setting mode
will automatically be cancelled and the time will not be saved to memory.
DEFINING THE VACUUMING AREA USING MAGNETIC TAPE
■
The magnetic tape
I1
serves to define the vacuuming area without you having
to close doors or place artificial obstacles in the path of the vacuum cleaner. The
vacuum cleaner will recognise the magnetic tape and will not travel over it. It will
start cleaning in another direction.
■
Place the magnetic tape before the place that the robotic vacuum cleaner should
not clean, for example room doorway, carpet, cables on the floor or a staircase with
rounded corners, etc.
■
To help the magnetic tape adhere better, you can attach it to the perimeter using
standard double-sided tape. It can also be cut into smaller pieces as required.
Additional tape can be purchased to extended the defined area.
Note
:
The magnetic tape must be put down prior to every cleaning session
because the robotic vacuum cleaner does not store the boundaries in
memory.
OPERATING THE ROBOTIC VACUUM CLEANER
Note:
Before starting the vacuum cleaner, always make sure that either
the dust container
A5
or the complete mop unit
A6
including the
respective HEPA dust filters is inserted inside.
TURNING ON THE ROBOTIC VACUUM CLEANER
■
Turn on the power supply to the vacuum cleaner using the main switch
A3
.
■
Press button
D1
. The button's indicator will start flashing blue. When the indicator
is permanently lit blue, the vacuum cleaner is in stand-by mode and ready for
operation.
STAND-BY MODE
■
The stand-by mode means that the vacuum cleaner is ready for operation. Button
D1
is backlit in blue colour.
■
Set the vacuum cleaner to the stand-by mode by pressing button
D1
on the vacuum
cleaner or buttons
C9
(ON/OFF) on the remote control either by turning on the
power supply using main switch or whenever while the vacuum cleaner is running.
SLEEP MODE
■
The sleep mode serves to save the battery's capacity. The vacuum cleaner enters
sleep mode either automatically after ten minutes of inactivity or when it is unable
to dock in the charging station. The backlight on button
D1
will turn off and the
vacuum cleaner will automatically switch to the sleep mode.
■
To wake the vacuum cleaner from the sleep mode to the stand-by mode, press
button
D1
on the vacuum cleaner or the control button
C9
(ON/OFF) on the remote
control.
Note:
When the vacuum cleaner is in sleep mode, it is not possible to wake it
up using the mobile phone application. In sleep mode, it reacts only to
buttons
D1
or
C9
(ON/OFF) on the remote control.
TURNING VOICE MESSAGES ON/OFF
■
If you prefer not to have the vacuum cleaner make system voice messages,
deactivate this function by simultaneously pressing buttons
C3
(PLAN) and
C4
(HOME) on the remote control. The vacuum cleaner will only make beeps.
■
If you wish to reactivate the voice messages, again simultaneously press the buttons
C3
(PLAN) and
C4
(HOME).
TURNING OFF THE ROBOTIC VACUUM CLEANER
■
If you wish to completely turn off the vacuum cleaner, set the main switch
A3
to
position
0
(off). The backlight on button
D1
will turn off and the power supply will
be shut off. When the vacuum cleaner is turned off, it will not respond to any button.
SELECTING THE ROBOTIC VACUUM CLEANER CLEANING MODE
■
Before starting the cleaning process, check that the entry door into your apartment
or house is closed. From the floor surfaces, remove clothing, paper, toys, power or
extension cords and other items that the vacuum cleaner could suck in or catch.
Lift curtains and drapes that reach to the floor so that the vacuum cleaner does not
catch them.
Tip:
When vacuuming in a new environment for the first time, carefully
observe the movement of the vacuum cleaner. You can thereby
recognise problematic obstacles and remove them for the next
cleaning session.
AUTOMATIC CLEANING MODE
■
Press button
D1
or button
C9
(ON/OFF) on the remote control. The vacuum cleaner
will enter the automatic cleaning mode, in which it effectively combines various
routes to achieve an optimal clean of the entire floor area. As soon as the vacuum
cleaner finishes cleaning, it will seek out the charging station and dock there to
recharge.
MAXIMUM POWER MODE
■
Press button
C12
(MAX) on the remote control. The vacuum cleaner will enter the
cleaning mode, in which it effectively combines various routes to achieve an optimal
clean of the entire floor area. This mode is characterised by increased motor and
central rotary brush power for the purpose of achieving the most effective cleaning
process.
ALONG-THE-WALLS CLEANING MODE
■
Repeatedly press button
C10
(MODE) on the remote control so that display
C2
shows
MODE1
. The vacuum cleaner will enter the along-the-walls cleaning mode,
in which it moves along the perimeter of the room and the motorised side rotary
brushes sweep out the dirt along the walls, furniture corners to achieve a perfect
clean. As soon as the vacuum cleaner finishes cleaning, it will seek out the charging
station and dock there to recharge.
2×2 METRE AREA (SPOT) CLEANING MODE
■
Place the vacuum cleaner approximately in the middle of the area that you wish
to clean.
■
Repeatedly press button
C10
(MODE) on the remote control so that display
C2
shows
MODE2
. The vacuum cleaner will enter the cleaning mode in which it will
move in straight parallel lines and vacuum an area of approximately 2 × 2 metres. As
soon as the vacuum cleaner finishes cleaning this area, it will seek out the charging
station and dock there to recharge.
RANDOM DIRECTION MOVEMENT MODE
■
Repeatedly press button
C10
(MODE) on the remote control so that display
E2
shows
MODE3
. The vacuum cleaner will enter the random direction movement
mode and will continue cleaning in this mode until the battery is almost flat. It
will then end the cleaning process and seek out the charging station in order to
recharge itself.
INTENSIVE CLEANING MODE
■
Repeatedly press button
C10
(MODE) on the remote control so that display
E2
shows
MODE4
. The vacuum cleaner will enter the intensive cleaning mode, where it
will clean the same location twice. It will then end the cleaning process and seek out
the charging station in order to recharge itself.
PAUSING THE CLEANING PROCESS
■
Press button
D1
or
C9
(ON/OFF) on the remote control at any time during the
cleaning process to stop the vacuum cleaner in the place where it is cleaning.
USING THE MOP UNIT
■
The mop unit is used for simultaneous vacuuming and dry or wet wiping of smooth
floor surfaces. It consists of the removable dust container
E1
, water tank
E2
and the
mop fabric
E3
. The water tank is equipped with an electronically-controlled water
pump that automatically doses the water on to the fabric and also stops dosing
water at the end of the cleaning process to prevent water from leaking on to the
floor or the charging station.
Attention:
Only use the mop unit intended for this type of robotic vacuum
cleaner.
Do not use the water tank
E2
without the mop fabric attached.
The mop unit is not intended for cleaning carpets.
Dry wiping of floors
■
Dry wiping is used for removing fine dust and floor polishing.
■
If the mop unit is inserted inside the vacuum cleaner, press latch
A7
and slide the
unit out of the vacuum cleaner.
■
Attach the mop fabric to the underside of the water tank using the velcro zip
E4
on
the water tank and insert the unit back into the vacuum cleaner.
■
Start the vacuum cleaner.
Wet wiping of floors
■
Wet wiping is used for cleaning away minor dirt and floor polishing
■
If the mop unit is inserted inside the vacuum cleaner, press latch
A7
and slide the
unit out of the vacuum cleaner.
