8
M965652 Rev. 1.5 (1/16)
A
HAND WASH SENSOR OPERATION; Fig. 1
When the Sensor detects a user, the water immediately starts
to flow. Water flow will stop 2 seconds after user is out of
sensor range. The off delay allows the user to comfortably
move his hands without the flow cycling on and off. As a
precaution, a safety timer will turn off the water after the
sensor has been blocked for 59 seconds. The water will stay
off until the blockage is removed from the detection zone.
Detection Zone: 2" - 10" (50mm - 250mm)
Default: Set at Factory 6" (150mm)
B
CHANGE SENSOR RANGE;
(Factory set at 6") Fig. 2, 2a
1. RemoveCONTROLBOX.DisconnectPowerSupply(1),
then reconnect.
Fig. 2.
2.WhiletheSENSORCONTROLLED (2) is blinking slowly,
placeyourhand1-2in.(30-50mm)infrontofthesensor.
Fig. 2a.
3.WhentheLEDstopsblinkingandstays“ON”,moveyour
handtothedesiredpositionandholdinplaceuntiltheLED
begins to blink again.
Fig. 2a.
4.OncetheSENSORCONTROLLED (2) begins to blink
again, remove your hand from the detection zone. When the
flashing stops, the detection distance is set.
5. Reinstall CONTROLBOXCOVERS(2). Tighten cover
screws firmly.
C
CLEAN FILTER ASSEMBLY; Fig. 3
1. Remove CONTROLBOXCOVER.
2. Close SUPPLY STOP (13)with4mmHexwrench.
Note: Activate sensor to keep water flowing out of
faucet while shutting off.
3.UnthreadFILTERASSEMBLY (6)usinga7/16
"
socket.
4.PullouttheFILTERASSEMBLY(6), remove and clean
white debris cup and filter screen.
5.InstalltheFILTERASSEMBLY(6) back in its place and
tightenwitha7/16
"
socket.
Caution: Do not over tighten.
6. Open SUPPLY STOP (13) with4mmHexwrench.
7. Reinstall CONTROLBOXCOVER.Tightencover
screws firmly.
Fig 1
5
6
4
10
3
DETECT
ION
ZONE
Fig. 2
1
Fig. 2a
1" - 2" (30mm - 50mm)
BLINKING LED
UP TO 10" (250mm)
BLINKING
LED
2
2
6
WHITE
DEBRIS
CUP
FILTER
SCREEN
••
••
••
••
••
••
•••
••
••
••
••
••
••
••
•••
••
••
••
••
••
••
••
•••
••
••
••
••
••
••
••
•••
••
••
••
••
••
••
••
•••
••
••
••
••
••
••
••
•••
••
••
••
••
••
••
••
•••
••
••
••
••
••
••
••
•••
••
••
••
••
••
••
••
•••
••
••
••
••
••
••
••
•••
••
••
••
••
••
••
••
•••
••
••
••
••
••
••
••
•••
••
••
••
••
••
••
••
•••
••
••
••
••
••
••
••
•••
••
Fig. 3
7/16" SOCKET
4mm HEX WRENCH
13
CAUTION
Before opening CONTROL BOX
disconnect AC power supply.
MAINTENANCE
