Selectronic 6059.193 Installation Instructions Manual Download Page 6

M 9 6 5 2 7 1

FOR AC-VERSION

(MULTI HOOK-UP); Fig. 2, 3

Unit #1

Unit #2

Unit #3

1. 

See AC Version Electrical Hook-up for first unit of the 

Multi hook-up.

2.

 Remove ENCLOSURE COVERS from all 

ENCLOSURES. 

 

3.

 Remove SOLID BLACK INSERT

(1)

 from right side 

of ENCLOSURE #1 and replace with gray 2-PIECE 

GROMMET 

(3)

. Replace solid black inserts on Unit #2 

with gray 2-PIECE GROMMET 

(3)

.

4.

 Take the 10 ft. EXTENSION 

(2)

 from Unit #2 and 

install into right side of Unit #1 and Left side of Unit #2 

insealing wire into SPLIT PLUG 

(7)

 as shown in 

Fig. 3a.

 

Push SPLIT PLUG 

(7)

 into GROMMET 

(8)

.

 

5.

 Insert CONNECTOR from 10 ft. EXTENSION 

(2)

 into 

CIRCUIT BOARD RECEPTOR 

(4)

 top of Unit #1 as 

shown in 

Fig. 2.

6.

 Insert other end of 10 ft. EXTENSION into LOWER 

U GROMMET 

(5)

 of Unit #2 (approximately 4" from 

connector). Fig. 3.  Push SPLIT PLUG 

(7)

 into 

GROMMET 

(8)

 to seal.

7.

 Insert connector of 10 ft. EXTENSION into lower 

receptor as shown in fig. 3 on CIRCUIT BOARD 

(6)

 of 

Unit #2.

8.

 Feed gray sensor wire 9  from Unit #2 through upper 

U GROMMET 

(10)

 of Unit #2 ENCLOSURE 4" from 

connector 

Fig. 3.

 Insert wire into SPLIT PLUG 

(7)

Push SPLIT PLUG 

(7)

 into GROMMET 

(8)

 to seal. 

Fig. 3a.

9.

 Insert GROMMET 

(2)

 back into ENCLOSURE. 

Fig. 3b

.

10.

 Reinstall Circuit Board 

(3)

 into Enclosure with all 

wires under Board. 

Fig. 3b.

11.

 Connect Unit #2 Red and Black Sensor wires To #2 

solenoid valve (Red to +, Black to -). 

Fig. 3b.

12.

 Repeat Steps 3 through 11 for remaining Units in 

Multi Hook-up.

Fig. 2

Fig. 3a

2                                                                 

5

TWO PIECE

TWO PIECE

GROMMET

GROMMET

TWO PIECE

TWO PIECE

GROMMET

GROMMET

2

1

5

6

1

3

4

4

10

3

9

3

1

1

1

Feed the gray 8 ft. EXTENSION (2)  through ROUND 

GROMMETS (3) and U GROMMETS (5) as illustrated above. 

2

7

2

8

RED

RED

3

BLACK

BLACK

1

Fig. 3b

4"

Summary of Contents for 6059.193










Reviews: