manualshive.com logo in svg

Selectronic Australia SE10, Operating Manual

Share
Download
Selectronic Australia SE10 Operating Manual Download Page 3

SE10 Manual

1

Selectronic Australia

Introduction

Thank you for choosing to purchase the Selectronic SE10 TRUE SINE
WAVE inverter. Many hours of Research and Development have gone
into the SE10 to ensure this inverter provides you with many years of
reliable service

Warranty Card

It is imperative that you complete your warranty card NOW. Your SE10 is
covered by a TWO year warranty. This warranty is in addition to your
rights under the trade practices act of your state or territory.
Returning you completed warranty card will enable us to register your
warranty and avoid any possible delays should service be required. If you
have any comments about our product that will not fit on the warranty card
please feel free to drop us a line. Yes, constructive criticism will also be
welcome.

Installation

200mm

200mm

200mm

SE10
Inverter

Front

200mm

SE10 Inverter

Please leave a clearance of 200mm on all sides and top of the Inverter.
The SE10 must be installed in a dry, cool, dust-free environment.
It is recommended that the inverter be placed as far from any radio
receivers as possible.

Summary of Contents for SE10

























Reviews:

No comments

Brands by name

Popular brands

Load more brands