manualshive.com logo in svg

Selectronic Australia SE10, Operating Manual

Share
Download
Selectronic Australia SE10 Operating Manual Download Page 14

SE10 Manual

12

Selectronic Australia

Indicator

Setting

LED (1) ON

LED (2) ON

LED (3) ON

LED (4) ON

ALL LEDs ON

16 watts

12 watts

8 watts

4 watts

Inverter will remain ON at all times. This could
be used if a fax machine or VCR is required to
stay on at all times. Be aware that this will use
more power from your battery.

Low Volts Adjust LED (6) (red) ON

To avoid total discharging of your battery the SE10 shuts down at a pre-set
low voltage. As all batteries are different, so too is the minimum voltage they
should be discharged to. The SE10 will leave the factory with a setting of

22.0 volts

, change this setting if required.

Hold the Mode button (7) down until LED (6) comes ON, (approximately 2
seconds) indicating you are ready to adjust this setting. Now press the Mode
button (7) until the desired value is sought. LEDs (1) – (4) will return to
either Status or Voltmeter after 20 seconds.

Indicator

Setting

LED (1) ON

LED (2) ON

LED (3) ON

LED (4) ON

23.0 volts

22.0 volts

21.0 volts

20.0 volts

Summary of Contents for SE10

























Reviews:

No comments

Brands by name

Popular brands

Load more brands