Selden 472-630-02 Manual Download Page 26

Page: 26 / 28

7 Warranty

Seldén Mast AB guarantees the S30/S40/S48/S54 winches for 2 years. The guarantee covers faults arising

from defective design, materials or workmanship.

The guarantee is only valid if the product is assembled, operated and maintained in accordance with this

manual and is not subjected to loads in excess of those indicated in the brochure and on the Seldén

website.

Complete shipment and warranty conditions are to be found on Seldéns website www.seldenmast.com.

See Resources/Partners information/General information/General conditions of sale (595-546-E).

If the system is repaired or modified by anyone other than Seldén Mast AB or one of our authorized dealers,

the guarantee ceases to be valid.

Seldén Mast AB reserves the right to alter the content and design without prior warning.

Summary of Contents for 472-630-02





























Search results

Summary of Contents for 472-630-02

Reviews:

Related manuals for 472-630-02

Brands by name

Popular brands

Selden 472-630-02, Manual

Search results

Summary of Contents for 472-630-02

Reviews:

Related manuals for 472-630-02

Brands by name

Popular brands