GIW01MR001SE 033173 270919
6
will regulate the room temperature according to the set weekly program.
6. On the contrary, with the ‘No’ option, the programmable thermostat goes back to the previous screen without saving the changes.
7.
Through the keys ‘ ‘ and ‘ ‘ select the option ‘EXIT’ or push the key ‘ ‘ or
wait 15 seconds without pushing any button.
Sound
With this parameter it is possible to set the sound emitted by the device when using the buttons; this parameter can be set to: beep, click or silent.
1.
Push the button ‘
‘; the display shows the menu.
2.
On the menu ‘Sound’, press the key ‘
‘.
3.
Select with the keys ‘ ‘ and/or ‘ ‘ which key sound is desired to set; push the button ‘
‘ to confirm the choice and the display shows
the confirmation of the selected sound.
4.
To exit the menu, select the option ‘EXIT’ or push the key ‘ ‘ or
wait 15 seconds without pushing any button.
Advanced
In this menu it is possible to set the following parameters:
• Mode
• Mod. manual
• Antifreeze
• Offset
• Hysteresis
•
Enable config.
•
Disable config.
• Default
Mode
This setting allows to invert the functioning logic of the relay, depending whether a heating or cooling system is being used.
The programmable thermostat is set to heating mode by default.
In order to modify the functioning logic, the following procedure must be carried out:
1.
On the ‘Mode’ menu, press the key ‘
‘.
2.
Select with the keys ‘ ‘ and/or ‘
‘ which mode it is necessary to set (Heating or Cooling); press the button ‘ ‘ to confirm the choice.
The display shows the confirmation message that the desired mode has been set.
3.
To exit the menu, select the option ‘EXIT’ or push the key ‘ ‘ or
wait 15 seconds without pushing any button.
Mod. Manual
This parameter defines the kind of manual regulation of the room temperature when the user activates the manual mode using the keys ‘
‘ and/or
‘
‘ from the home screen or via App.
The parameter allows the choice between two options: Temporary manual mode or Permanent manual mode.
Temporary manual mode
The wi-time regulates the room temperature according to the setpoint configured manually, until 23:59 of the current day.
Permanent manual mode
The wi-time regulates the room temperature according to the setpoint configured manually permanently or until the user voluntarily disable it.
In order to configure this parameter proceed as follow:
1. On the ‘Mod. Manual’ option, press the key ‘ ‘.
2.
Select with the keys ‘ ‘ and/or ‘ ‘ which mode to set; press the key ‘
‘ to confirm the choice.
The display shows the confirmation message that the desired mode has been set.
3.
To exit the menu, select the option ‘EXIT’ or push the key ‘ ‘ or
wait 15 seconds without pushing any button.
For further details about the activation of the set manual mode, see chapter ‘Room temperature regulation’.
Antifreeze
The Antifreeze function allows to select a minimum temperature which is maintained when the programmable thermostat is on, in heating mode and
on the current time slot no temperature of Comfort or Economy is defined; this function allows to preserve the environment and the system if
the room
temperature drops below the set value. The device is set by default with the Antifreeze function to +3°C.
ATTENTION
The function is active only if the device has been set in Heating mode.
In order to regulate the Antifreeze temperature, proceed as follows:
1.
On the ‘Antifreeze’ option, push the button ‘
‘.
2.
Set with the keys ‘ ‘ and/or ‘ ‘ the Antifreeze temperature; press the key ‘
‘ to confirm the choice.
3.
To exit the menu, select the option ‘EXIT’ or push the key ‘ ‘ or
wait 15 seconds without pushing any button.
Offset
With this parameter it is possible to correct the temperature detected by the sensor of ±5°C, in order to correct any systematic reading errors which
happen because of the positioning of the programmable thermostat/remote sensor in unsuitable areas for detecting the room temperature.
The device is set by default with the Offset set to 0.0°C.
