GIW01MR001SE 033173 270919
3
OPERATION
Starting up
•
Associate the programmable thermostat with the App as described on the paragraph “PAIRING THE PROGRAMMABLE THERMOSTAT AND APP”.
•
Set the programmable thermostat operating mode on Heating (set by default) or Cooling.
Functioning logic
On ‘Heating’ mode, when the detected room temperature, through the internal sensor or alternatively with the external sensor, is lower than the set
one
(manually or by program)
, the wi-time activates the relay to start the boiler and the symbol
‘
‘ appears on the display.
On ‘Cooling’ mode, when the detected room temperature, through the internal sensor or alternatively with the external sensor, is higher than the set
one
(manually or by program
)
,
the wi-time activates the relay to start the
cooling system and the symbol ‘ ‘
appears on the display.
Display visualization
When operating normally, the display shows:
- The current time regulated through Wi-Fi or set manually.
- The detected room temperature.
- The symbol of the Wi-Fi connection (
) or the configuration mode symbol ( ).
- Under the line, on the lower part of the display, the setpoint temperature is shown. If the device is on ‘Heating‘ mode and it is warming to reach the
setpoint temperature (set manually or by program) the writing ‘Heats up to’ and the setpoint temperature appear. If the device is on ‘Cooling’ mode
and it is cooling the room to reach the setpoint temperature (set manually or by program) the writing ‘Cool down to’ appears and, subsequently, the
setpoint temperature.
Room temperature regulation
The room temperature regulation can happen in two configurable ways, described as follows.
Program
This mode can be activated directly on the wi-time or via App.
This mode, which time slots can be managed exclusively via Seitron smart App, allows to activate the adjustment of the room temperature according
to the set weekly program.
Details:
- The programmable thermostat regulates the room temperature according to the set program.
These are the regulations modes:
In Heating mode: Antifreeze, Comfort or Economy.
In Cooling mode: Off, Comfort or Economy.
- Normally on Heating mode, in order to get an economy night mode, the economy temperature should have a lower value than the comfort one. On
the contrary, when on cooling mode, the economy temperature should have an higher value than the comfort one.
Manual
This mode, which can be activated directly on the wi-time or via App, allows to manually regulate the room temperature independently from the time
program, according to the mode set on the user parameter ‘Mod. manual’ or on the App settings.
This mode can be activated acting on the buttons ‘ ‘ or ‘ ‘ as described in the following:
- Push one time the button ‘
‘ or ‘
‘.
- The display shows ‘Change setpoint’ and the related configured setpoint temperature.
- By furtherly pressing the buttons ‘
‘ or ‘
‘ the setpoint temperature can be modified and the wi-time switches automatically to the ‘manual’
regulation mode.
If the user parameter ‘Mod. manual’ has been set to ‘Manual temporary’ the display shows the symbol ‘
‘; this mode will be active until 23.59
of the current day.
On the contrary, if the user parameter ‘Mod. manual’ has been set to ‘ Manual permanent’ the display shows the symbol ‘
‘; this mode will be active
until it is disabled voluntarily.
ATTENTION
If it is necessary to go back to the ‘Program’ setting, follow the procedure described in SETTING USER PARAMETERS PROGRAM.
Boost
This mode can be activated exclusively via the App Seitron smart.
By activating this mode, the programmable thermostat compels the system to turn on in heating or cooling mode (depending on the setting made) for
a time which can be set to 30, 60 or 90 minutes independently from the setpoint temperature.
This function is activated if it is needed to warm up or chill an environment particularly hot or cold.
SWITCHING OFF
In order to switch off the programmable thermostat, push the button ‘
‘ for at least one second. The display shows the writing ‘ OFF ’.
KEYBOARD LOCK
By pushing at the same time the soft buttons
‘ ‘ and ‘ ‘ when on main screen or when the programmable thermostat is off, it is possible to lock
the keyboard so that it won’t be possible to tamper the device or accidentally press some button. The keyboard lock is confirmed on the display with
a message and the symbol ‘
‘. To unlock the keyboard, press at the same time the keys ‘
‘ and ‘
‘ again: the display shows a confirmation
message that the keyboard has been unlocked.
