manualshive.com logo in svg

Seip RP60A, Installation Instructions Manual, Page: 22 / 23

Share
Download
Seip RP60A Installation Instructions Manual Download Page 22

EC Declaration of Confirmity

in accordance with the Radio and Telecommunications 
Terminal Equipment Act (FTEG) and Directive 1999/5/EC 
(R&TTE Directive)

EG-Konformitätserklärung

gemäß dem Gesetz über Funkanlagen und Telekomm

unikationsendeinrichtungen (FTEG) und der Richtlinie 

1999/5/EG (R&TTE)

Grombacher Straße 83

75045 Walzbachtal-Jöhlingen

Germany

www.seip.com

TECHNIK

ANTRIEBS

ANTRIEBS

GmbH

We, 

Wir,

Seip Antriebstechnik GmbH

Grombacher Straße 83, 75045 Walzbachtal-Jöhlingen, Deutschland

declare that the product

erklären, daß das Produkt

SKR 433-1

Code B43A023004-1

Hand Transmitter as remote control for garage door operators

Handsender als Fernbedienung für Garagentorantriebe

(Short Range Device)

(Funkgerät geringer Reichweite (SRD))

complies with the essential requirements of §3 and the other relevant provisions of the FTEG (Article 3 of the R&TTE Directive),  

when used for its intended purpose.

bei bestimmungsgemäßer Verwendung den grundlegenden Anforderungen des §3 und den übrigen einschlägigen  

Bestimmungen des FTEG (Artikel 3 der R&TTE) entspricht.

§3(1)1, (Article 3(1)a)) does not refer to this type of product.

§3(1)1, Artikel 3(1)a) bezieht sich nicht auf diesen Produkttyp, es gibt hierzu keine Norm

Protection requirement concerning electromagnetic compatibility §3(1)(2), (Article 3(1)(b))

Schutzanforderungen in Bezug auf die elektromagnetische Verträglichkeit §3(1)2, Artikel 3(1)b))

EN 300 220-1/1997

EN 300 683/1997

EMV / EMC Directive 89/336/EEC;92/31/EEC;93/68/EEC

Myke Seip, Walzbachtal-Jöhlingen, 09.03.2010

Document No. FU-009032010

Dokument Nr. FU-009032010

and/und

SKR1W433

Code B43A623001

Wall Transmitter as remote control for garage door operators

Wandsender als Fernbedienung für Garagentorantriebe

(Short Range Device)

(Funkgerät geringer Reichweite (SRD))

complies with the essential requirements of §3 and the other relevant provisions of the FTEG (Article 3 of the R&TTE Directive),  

when used for its intended purpose.

bei bestimmungsgemäßer Verwendung den grundlegenden Anforderungen des §3 und den übrigen einschlägigen  

Bestimmungen des FTEG (Artikel 3 der R&TTE) entspricht.

§3(1)1, (Article 3(1)a)) does not refer to this type of product.

§3(1)1, Artikel 3(1)a) bezieht sich nicht auf diesen Produkttyp, es gibt hierzu keine Norm

Protection requirement concerning electromagnetic compatibility §3(1)(2), (Article 3(1)(b))

Schutzanforderungen in Bezug auf die elektromagnetische Verträglichkeit §3(1)2, Artikel 3(1)b))

EN 300 220-1 V2.1.1 
EN 300 220-2 V2.1.2
EN 301 489-1 V1.6.1 
EN 301 489-3 V1.4.1 

EN 60950-1:2006

EMV / EMC Directive 2006/95/EC;2004/108/EC; 99/5/EC

22

Summary of Contents for RP60A
























Reviews:

No comments