manualshive.com logo in svg

Seip RP60A, Installation Instructions Manual

Share
Download
Seip RP60A Installation Instructions Manual Download Page 13

HF-MODUL/RECEIVER CARD

KRAFT/

PRESSURE

LERN/LEARN

TEST/RUN

Vp

TEST/
FUNK

8k2/
DIAG

HF-MODUL/RECEIVER CARD

KRAFT/

PRESSURE

LERN/LEARN

TEST/RUN

Vp

TEST/
FUNK

8k2/
DIAG

HF-MODUL/RECEIVER CARD

KRAFT/

PRESSURE

LERN/LEARN

TEST/RUN

Vp

TEST/
FUNK

8k2/
DIAG

HF-MODUL/RECEIVER CARD

KRAFT/

PRESSURE

LERN/LEARN

TEST/RUN

Vp

TEST/
FUNK

8k2/
DIAG

13

Printed Circuit Board: Adjustments and Connections

Programming the Soft-Modes

The RP60 is shipped with factory pre-set values for the Soft-
Modes; if the learning cycle is run without any changes to the 
factory-settings, then the pre-set values will be programmed 
automatically.

The BOTTOM Soft-Stop

The length of the BOTTOM Soft-Stop may be changed during the 
first run of the learning-cycle in closing direction.

- 

Extending 

the BOTTOM Soft-Stop is recommended, if the  

garage door slams on closing.

- 

Reducing or disabling

 the BOTTOM Soft-Stop is recommen-

ded, when the bottom of the garage door does not close comple-
tely. Expecially when mechanical spring-locks are installed, these 
might not engage. When the BOTTOM Soft-Stop is disabled, the 
garage door reaches the closing position with a higher speed. This 
gives the door a higher momentum and the bottom can fall into 
the doors‘ frame - the locks can then engage. 

Programming the BOTTOM Soft-Mode

The length of the soft-stop can be adjusted during the first au-
tomatic measurement-run in closing direction. Please proceed as 
described below:

1. Start the learning cycle (refer to page 11)
2. the operator runs in closing direction with low speed
3. press the LERN/LEARN button and keep it pressed - the operator 
is now increasing the speed
4. release the LERN/LEARN button at the position where the soft-
stop shall begin 

(the operator will safe this position as the 

beginning of the BOTTOM soft-stop)

If the Soft-Stop is to be disabled, then the LEARN button must be 
pressed until the door is completely closed.
5. the operator will reduce speed with a short delay and then 
reach the closing position
6. the operator will procede with the remaining measurement-
runs

When the operators‘ light stops blinking, all measured values 
are saved in the memory - the BOTTOM soft-stop now is in the 
programmed position.

Enabling the TOP Soft-Modes

The RP60 will start the closing procedure from OPENING posi-
tion with slow speed (e.g. TOP Soft-Mode). Dependant on the 
performance of the garage door it might be necessary to enable 
this Soft-Mode, especially when the operator reverses during that 
period (e.g. pressure detection).

Procedure for Enabling the TOP Soft-Mode

Remove the jumper „KRAFT/PRESSURE“ before starting the  
learning cycels and leave it removed until the learning cycles are 
completed - the TOP Soft-Mode then is enabled. 
After the learning cycles the Jumper „Kraft/Pressure“ fulfills its‘ 
normal function („Normal Force/Higher Force during CLOSING 
Soft-Stop“ as to page 10) and can be replaced.

TIP: should you decide to remove the jumper, then plug it 
back  onto one pin only - so it remains available on the P.C.B. 
for later use.

 

Quick Reference „Programming the BOTTOM Soft-Mode“

1.) During the first learning 
cycle in CLOSING direction

Keep the LERN/LEARN button 
pressed during the first run in 
CLOSING direction and keep it 
pressed -the operator increases 
speed 

2.) The operator is running 
in CLOSING direction with 
increased speed

Release the LERN/LEARN button 
at the position where the soft-
stop shall start in future.

If the LEARN button is kept 
pressed until the door is  
completely shut, then the  
soft-stop will be disabled.

3.) The operator reaches the CLOSED position. It will proceed 
with the learning-cycle (two more runs) before finishing the pro-
gramming. The CLOSING Soft-Stop will then be set as to your 
adjustments.

Quick Reference „Enabling the TOP Soft-Mode“

1.) Remove the Jumper KRAFT/PRESSURE before starting the 
learning cycles

2.) Start the learning cycle

3.) After the learning cycles are completed the jumper can be 
replaced (dependant on the required function, as to page 10)

TOP soft-mode

BOTTOM soft-mode

Special Functions

Summary of Contents for RP60A
























Reviews:

No comments

Brands by name

Popular brands

Load more brands