background image

Cal. 5M54A

2/22

SPECIFICATIONS

10 seconds

20 seconds

30 seconds

Between 7 days and 1 

month

Approx.

1 month

Approx. between

4 and 6 months

Between

1 and 7 days

5 seconds

POWER RESERVE

QUICK MOVEMENT OF 

SECOND HAND

SEIKO  KINETIC  Cal.  5M54  is  an  analogue  quartz  watch  equipped  with  the  Kinetic  technology 
developed by SEIKO. It generates the electric energy to power the watch, utilizing the movement of 
your body, and stores it in the rechargeable battery, which requires no periodical replacement unlike 
conventional button-type batteries.

1.  When the watch stops completely, or if you find 

the second hand moving at two-second intervals, 
swing  the  watch  from  side  to  side  at  a  rate  of 
twice a second.

1.  By swinging the watch

2.  By using the KINETIC Energy Supplyer YT02A  

2.  250 swings will reserve up to 1 day of power.  
 

The second hand will start moving at one-second intervals.

Set the crown to the 5M position. 
•  Make  sure  that  the  watch  is  correctly 

positioned as it may affect the amount of 
power generated.

•  The amount of power generated may vary 

depending the models of the watch. 

5M

Cal. 5M54A is equipped with a power reserve indicator. The current power reserve can be checked by 
reading the posisiton of the second hand after pressing the button at the 2 o'clock position.

*  The second hand will resume normal movement after the indicated 5, 10, 20 or 30 seconds have 

elapsed.

*  To allow easy reading of the second hand, press the button when the second hand is at the 12 o’clock 

position.

*  It is recommended that the watch be swung further until 2 days of power is reserved.  As a 

guideline  of  recharging,  additional  200  to  250  swings,  about  450  to  500  swings  in  total  will 

reserve 2 days of power.

power reserve indicator

POWER

RESERVE

NUMBER OF

SWINGS

250

450 ~ 500

1 DAy

2 DAyS

APPROX.

6 MONTHS

FULL

FeatUres

How to cHarGe tHe watcH

TG 5M54A.indd   2

08.9.25   2:14:20 PM

Summary of Contents for 5M54A























Reviews: