background image

7

PARTS CATALOGUE

Cal. 5J22A

Remarks:

8

Date dial

Part code

0878 936

3 o’clock

Color of figure

Color of

background

White

Black

Position of crown

4 o’clock (outer)

Position of

calendar frame

0878 937

3 o’clock

Black

White

4 o’clock (outer)

0878 940

3 o’clock

White

Black

4 o’clock (inner)

0878 941

3 o’clock

Black

White

4 o’clock (inner)

The type of date dial is determined based on the design of cases.  (The table above does not cover all
the date dial available.)
Check the case number and refer to “SEIKO Casing Parts Catalogue” to choose a corresponding date
dial.

56

Winding stem   0351 557

The type of winding stem is determined based on the design of cases.

Check the case number and refer to “SEIKO Casing Parts Catalogue” to choose a corresponding
winding stem.

TECHNICAL GUIDE

Cal. 5J22A

The explanation here is only for the particular points of Cal. 5J22A.

For the repairing, checking and measuring procedures, refer to the “TECHNICAL GUIDE, GENERAL
INSTRUCTIONS”.

I.

STRUCTURE OF THE CIRCUIT BLOCK

Automatic generating

input terminal

Input terminal (+)

Input terminal (–)

Second coil output terminal

Crystal unit

C-MOS-IC

Hour and minute coil
detection terminal

Hour and minute coil output terminal

Summary of Contents for 5J22A






















Reviews: