manualshive.com logo in svg

SeeMeCNC ERIS DELTA, Manual

Share
Download
SeeMeCNC ERIS DELTA Manual Download Page 51

Show Reset Connection

 should be checked on the Eris®.  It will present a “Reset 

Connection” button in the printer connection bar that can be used as an emergency stop.

Show Firmware Updater

 should be set to “Simple Arduino” for the Eris®.  This controls 

a feature that allows MatterControl to send firmware updates directly to the printer.

 

For a stock Eris®, 

Extruder Count

 should be set to 1.  If you add an additional extruder 

in the future, you can tell the slicing engine about it here.

Heat Before Homing

 will force the nozzle to heat up to operating temperature before 

homing.

 

Share Temperature

 is used when utilizing multiple extruders that share the same heat 

source.

 

The 

Firmware

 section allows you to tell the slicing engine about the firmware you're 

using with your Eris®.

 

G-code Output

 specifies what

“flavor” of G-code should be created by the
slicing engine.  For the Eris®, this should
be set to 

REPRAP

.

 

51

Summary of Contents for ERIS DELTA








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands